manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

5.16

SHIFTER SHAFT

INSTALLATION

1.

See 

Figure 5-94

. Correctly install shifter return spring onto

the reverse side of the shifter shaft assembly before pla-
cing shaft in left crankcase half.

NOTE

See 

Figure 5-95

. The shifter shaft return spring can be installed

incorrectly and then assembled in the left crankcase half.
Failure to install the spring properly will result in improper
shifting.

2.

See 

Figure 5-97

. Depress ratchet arms and insert shaft

assembly into the bushing in the left case half and release.
Ratchet arms should now be inside the end plate of the
shifter drum contacting the shifter drum pins.

3.

See 

Figure 5-98

. Apply several drops of LOCTITE 271

(red) to last few threads of countershaft retaining screw.
Thread screw into end of shaft.

4.

Place transmission in gear and tighten hex head fastener
to 33-37 ft-lbs (44.7-50.2 Nm).

5.

Install transmission sprocket. See 

5.17 TRANSMISSION

SPROCKET

.

6.

Continue assembling engine. See the following:

•

3.18 CRANKCASE, Assembly

•

3.7 CYLINDER HEAD, Assembly

•

3.7 CYLINDER HEAD, Cylinder Head Installation

•

3.8 CYLINDER AND PISTON, Assembly/Installation

7.

Install primary chain and engine sprocket, clutch assembly
and primary cover. See 

5.6 PRIMARY CHAIN

.

8.

Install engine in chassis. See 

3.6 ENGINE INSTALLA-

TION

.

sm00345

Figure 5-94. Shifter Shaft Return Spring (Correctly

Installed)

sm00346

Figure 5-95. Shifter Shaft Return Spring (Incorrectly

Installed)

1

2

3

sm00310

1.

Shifter shaft

2.

Return spring

3.

Ratchet arms

Figure 5-96. Shifter Shaft Assembly

HOME

2010 XB Service: Drive/Transmission  5-55

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

Racelogic VBOX Video HD2 Assembly Manual preview
VBOX Video HD2
Brand: Racelogic Pages: 2
HYOSUNG GD250 Owner'S Manual preview
GD250
Brand: HYOSUNG Pages: 98
X-lite X-901 Directions For Use Manual preview
X-901
Brand: X-lite Pages: 84
hepco & becker Minirack 6602533 01 01 Manual preview
Minirack 6602533 01 01
Brand: hepco & becker Pages: 4
Honda NSC110 2020 Manual preview
NSC110 2020
Brand: Honda Pages: 137
hepco & becker 630727 00 01 Manual preview
630727 00 01
Brand: hepco & becker Pages: 3
Yamaha XV17ATMV(C) Road Star Owner'S Manual preview
XV17ATMV(C) Road Star
Brand: Yamaha Pages: 108
Yamaha XT250P Owner'S Manual preview
XT250P
Brand: Yamaha Pages: 100
Yamaha XTZ12D(C) Owner'S Manual preview
XTZ12D(C)
Brand: Yamaha Pages: 118
Yamaha Super Tenere ES 2022 Owner'S Manual preview
Super Tenere ES 2022
Brand: Yamaha Pages: 132
Yamaha XT250X 2008 Service Manual preview
XT250X 2008
Brand: Yamaha Pages: 282
Yamaha Super Tenere ES 2020 Owner'S Manual preview
Super Tenere ES 2020
Brand: Yamaha Pages: 130
Yamaha TDM850 User Manual preview
TDM850
Brand: Yamaha Pages: 211
Garmin Montana 7 Series Installation Instructions Manual preview
Montana 7 Series
Brand: Garmin Pages: 24
Suzuki Intruder VS1400 Service Manual preview
Intruder VS1400
Brand: Suzuki Pages: 291
hepco & becker 506300 Quick Start Manual preview
506300
Brand: hepco & becker Pages: 2
hepco & becker 611.793 00 02 Assembling Instructions preview
611.793 00 02
Brand: hepco & becker Pages: 4
Yamaha XS360 Service Manual preview
XS360
Brand: Yamaha Pages: 34

Brands by name

Popular brands

Load more brands