manualshive.com logo in svg

Buell XB 2010, Service Manual

The Buell XB 2010 Service Manual is a comprehensive manual providing detailed instructions and guidance for servicing and maintaining your Buell XB 2010 model. Available for free download, this manual is a must-have resource for all Buell XB 2010 owners. Get yours now exclusively from manualshive.com.

Share
Download
background image

5.6

PRIMARY CHAIN

GENERAL

Since the primary chain runs in lubricant, little service will be
required other than checking lubricant level and chain tension.
If, through hard usage, the primary chain does become worn
and cannot be adjusted to within specifications, it must be
replaced. See 

1.10 PRIMARY CHAIN

.

An opening between the primary drive and transmission com-
partments allows the same lubricant supply to lubricate moving
parts in both areas.

REMOVAL

TOOL NAME

PART NUMBER

SPROCKET LOCKING LINK

HD-38362 FOR XB9
MODELS

SPROCKET LOCKING LINK

HD-46283 FOR
XB12 MODELS

TWO CLAW PULLER

HD-97292-61

To prevent accidental vehicle start-up, which could cause
death or serious injury, disconnect negative (-) battery
cable before proceeding. (00048a)

1.

Remove negative battery cable from battery.

2.

Drain the transmission fluid. See 

1.9 CLUTCH/TRANSMIS-

SION/PRIMARY FLUID, Transmission Fluid

.

3.

Remove primary cover. See 

5.3 PRIMARY COVER

.

4.

Loosen engine sprocket.

a.

See 

Figure 5-23

. Install SPROCKET LOCKING

LINK (Part No. HD-38362 for XB9 models) or
SPROCKET LOCKING LINK (Part No. HD-46283 for
XB12 models).

b.

Remove the engine sprocket bolt.

c.

Loosen but do not remove engine sprocket. If neces-
sary, use the slotted portion of TWO CLAW
PULLER (Part No. HD-97292-61) and two bolts to
loosen the engine sprocket.

5.

See 

Figure 5-24

. Remove adjusting screw assembly.

a.

Remove large retaining ring (1).

b.

Remove adjusting screw assembly from pressure
plate.

NOTE

See 

Figure 5-25

. Mainshaft nut has left-hand threads. To pre-

vent damage, turn nut clockwise to loosen and remove from
mainshaft.

6.

Remove mainshaft nut and washer.

7.

Remove the clutch, clutch shell/hub, primary chain and
engine sprocket as a unit.

sm00289

Figure 5-23. Sprocket Locking Link Tool (Specific tool for

XB9 models, Specific tool for XB12 models)

3

2

1

4

sm00282

1.

Retaining ring

2.

Bearing and release plate

3.

Retaining ring

4.

Adjusting screw

Figure 5-24. Adjusting Screw Assembly

HOME

2010 XB Service: Drive/Transmission  5-17

Summary of Contents for XB 2010











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XB 2010

X-lite CLEO Installation Instructions preview
CLEO
Brand: X-lite Pages: 5
BRUUDT Yamaha X-MAX 300 Mounting Instructions preview
Yamaha X-MAX 300
Brand: BRUUDT Pages: 7
Bajaj Pulsar 150 DTS-i Maintenance Manual preview
Pulsar 150 DTS-i
Brand: Bajaj Pages: 41
AGV CORSA R Manual preview
CORSA R
Brand: AGV Pages: 45
kellermann Jetstream Installation Manual preview
Jetstream
Brand: kellermann Pages: 7
Yamaha STAR XV19CSX(C) Owner'S Manual preview
STAR XV19CSX(C)
Brand: Yamaha Pages: 96
Yamaha Star XV19CTSX Owner'S Manual preview
Star XV19CTSX
Brand: Yamaha Pages: 102
Yamaha star 2012 Owner'S Manual preview
star 2012
Brand: Yamaha Pages: 100
Yamaha Star XV250B 2011 Owner'S Manual preview
Star XV250B 2011
Brand: Yamaha Pages: 98
Shad SH39 Owner'S Manual preview
SH39
Brand: Shad Pages: 2
Shad KIT TOPMASTER S0BN11ST Quick Start Manual preview
KIT TOPMASTER S0BN11ST
Brand: Shad Pages: 2
Shad KIT TOPMASTER S0SV69ST Quick Start Manual preview
KIT TOPMASTER S0SV69ST
Brand: Shad Pages: 2
Shad KIT TOPMASTER S0GL69ST Quick Start Manual preview
KIT TOPMASTER S0GL69ST
Brand: Shad Pages: 2
JETPRIME JP CJP 082H Installation Manual preview
JP CJP 082H
Brand: JETPRIME Pages: 5
RIEJU MRT 50 EURO 5 Owner'S Manual preview
MRT 50 EURO 5
Brand: RIEJU Pages: 52
X-PRO XB27B-125 Manual preview
XB27B-125
Brand: X-PRO Pages: 3
X-PRO Marvel A09 Quick Manual preview
Marvel A09
Brand: X-PRO Pages: 3
Rockford Fosgate Prime R1-HD2-9813 Manual preview
Prime R1-HD2-9813
Brand: Rockford Fosgate Pages: 18

Brands by name

Popular brands

Load more brands