11.
For Firebolt models:
See Figure 4. Use a second cable
strap (1) to bind the right side heated hand grip wire,
handlebar switch harness and brake switch harness to
the upper fork clamp (2).
For Lightning models:
Use a
second cable strap to bind the right side heated hand
grip wire, handlebar switch harness and brake switch
harness together
behind
the upper fork clamp. DO NOT
bind the wires
to
the upper fork clamp.
For Ulysses
models:
See Figure 5. Use a second cable strap (2) to
bind the right side heated hand grip wire to the handlebar
switch harness and brake switch harness (3) at the
(lower) mark made on the handlebar switch harness in
Step 5.
For 1125R models:
See Figure 6. Hook the right
side heated hand grip wire, handlebar switch harness
and brake switch harness into the wire guide under the
right side of the upper fork clamp.
For ALL models:
Test
the throttle operation to verify that there is NO contact
between the hand grip wire and any part of the vehicle.
2
3
1
is04645
Wire previously strapped to cables
1.
Strap wire to brake and control harnesses at
this location
2.
Brake and hand control harnesses
3.
Figure 5. Bind Heated Grip Wire to Brake and Handlebar
Switch Harnesses (Ulysses Models)
is04883
Figure 6. Hook Wiring to Wire Guide (1125R Models)
2
1
is04646
Mark on left-side hand grip wire
1.
Inboard edge of handlebar switch
2.
Figure 7. Align Mark with Edge of Switch (Ulysses Model
Shown)
12. See Figure 7. Locate the mark (1) on the left side hand
grip wire, and align it with the inboard edge (2) of the
handlebar switch.
For Firebolt models:
Use a cable
strap from the kit to bind the left side hand grip wire,
handlebar switch harness and clutch interlock switch
harness together. See Figure 4. Use a second cable
strap (3) to bind the heated hand grip wire, handlebar
switch harness and interlock switch harness to the upper
fork clamp (2).
For Lightning models:
Use a cable strap
from the kit to bind the left side hand grip wire, handlebar
switch harness and clutch interlock switch harness to
the handlebar, close to the switch assembly. Use a
second cable strap to bind the heated hand grip wire,
handlebar switch harness and interlock switch harness
to the handlebar, close to the upper fork clamp. DO NOT
bind the wires
to
the upper fork clamp.
For Ulysses
models: For 1125R models:For 1125CR models:
a.
See Figure 8. Use two cable straps (1 and 2) from
the kit to bind the left side hand grip wire (3) to the
handlebar switch harness and clutch interlock
switch harness on either side of the harness
retainers (4).
b.
If the prongs on any of the harness retainers were
broken during disassembly, replace them with the
new
harness retainers from the kit. Press the
harness retainers into the holes in the left and right
sides of the handlebar.
c.
Use a cable strap from the kit to bind the left side
hand grip wire and handlebar switch harness
together.
d.
Hook the left side heated hand grip wire, handlebar
switch harness and clutch interlock switch harness
into the wire guide under the left side of the upper
fork clamp.
e.
Route the
left side
switch wiring harness along the
same path as the original switch wires,
through
the opening in the fairing support bracket.
f.
Route the
left side
heated grip harness through
the same opening in the fairing support bracket.
g.
Continue routing the left side handlebar switch
wiring harness and heated grip harness along the
vehicle main wire harness to the connector location
beneath the headlight assembly.
4 / 9
-J04491
