manualshive.com logo in svg

Buehler IsoMet 5000, Manual, Page: 42 / 76

Share
Download
Buehler IsoMet 5000 Manual Download Page 42

 

36 

MA112780_38.6 

[Original Instructions] 

9/19/2011 

Automatic Blade Dressing 

The Automatic Blade Dressing system uses a fine-tooth shaft for advancing the Dressing Stick, 
giving maximum cleaning cuts from the stick. Periodically this fine-toothed shaft will need to be 
clean. 

Cleaning the Automatic Blade Dressing shaft 

1.  Turn off the IsoMet 5000. 

2.  Open the hood. 

3.  Pull the T-mount out of the housing. 

4.  Using the supplied cleaning brush, clean the shaft thoroughly and lubricate with a light oil. 

Do 

not

 

use WD40™. 

5.  Carefully align T-mount and push it back into the housing. 

Checking the Blade Motor Total Hours 

To check the blade motor total operating time in hours:  

 

 

POWER

OFF

ON

IsoMet   5000

LINEAR PRECISION SAW

R

 

Figure 13

 Hidden Button on the Front Display Panel 

1.  There is a hidden, non-tactile button located on the front display panel. 

2.  Power off the IsoMet 5000. 

3.  Press and hold the hidden button on the front display panel, this will power on the machine.  

4.  The LCD Screen will now display BLADE HOURS. This is the total number of hours that the 

blade motor has been rotating. 

5.  Press the ZERO button to return to the normal operating screens. 

 

Hidden Button 
(No Dome) 

Summary of Contents for IsoMet 5000













































































Reviews:

No comments