Home
/
Buehler
/
IsoMet 5000
/
Manual

Buehler IsoMet 5000, Manual, Page: 32 / 76

Share

Page: 32 / 76

Buehler IsoMet 5000 Manual Download Page 32

26

MA112780_38.6

[Original Instructions]

9/19/2011

NOTICE

Too large of a specimen may cause the flange to advance into the specimen causing
damage to both the flange and specimen. If you need to cut large specimens, reposition
the specimen using a different mount.

During operation observe the s

aw’s performance. Due to differences in specimen

thickness and density/consistency, the FEED RATE parameter can be adjusted for
optimum cutting conditions.

If, at any time during the cutting mode, the operator lifts the cover, presses the CUTTING
CYCLE button to the OFF position, or the blade reaches the end of travel switch, the blade
will

immediately stop.

Manual Cutting

There are two (2) ways to manually cut a specimen.

Method 1

1. Mount the specimen as previously described.

2. Press the BLADE MOTOR and PUMP MOTOR buttons to the ON position.

3. Adjust the BLADE SPEED to the desired rpms.

4. Manually turn the crank to cut the specimen.

5. Retract the blade when the cut is complete.

6. Press the BLADE MOTOR and PUMP MOTOR buttons to the OFF position.

Method 2

1. Mount the specimen as previously described.

2. Press the BLADE MOTOR and PUMP MOTOR buttons to the ON position.

3. Adjust the BLADE SPEED to the desired rpms.

4. Press the FEED MOTOR button to the ON position.

5. When the cut is complete, press the BLADE MOTOR button to the OFF position. The BLADE

MOTOR and the FEED MOTOR will be deactivated.



When using Method B, the DISTANCE REMAINING field will count down to 0.00 and
continue into the negative numbers.

6. Retract the blade.

7. Press the PUMP MOTOR button to the OFF position..

«
...
30
31
32
33
34
...
»

Summary of Contents for IsoMet 5000













































































Reviews:

No comments