manualshive.com logo in svg

Buehler IsoMet 5000, Manual, Page: 35 / 76

Share
Download
Buehler IsoMet 5000 Manual Download Page 35

 

29 

MA112780_38.6 

[Original Instructions] 

9/19/2011 

Automatic Blade

 

Dressing, Rotating

 

Chuck, and Specimen

 

Positioning

 

System

 

The IsoMet 5000 is shipped with the Specimen Positioning System and Automatic Dressing System 
already attached. The following instructions are for replacing the Automatic Dressing System, the 
Specimen Positioning System, and a Rotating Chuck. 

There are three (3) power sockets in a vertical line located behind the control housing. 

 

The top power socket connects to the Specimen Position System. 

 

The middle power socket connects to the Rotating Chuck. 

 

The bottom power socket connects to the Automatic Blade Dressing. 

 

Figure 12 IsoMet Power Sockets 

Removing the Specimen Position System

 (Catalog Number 11-2699)

 

1.  Turn OFF the IsoMet 5000. 

2.  Disconnect the power cable from the control housing. 

3.  Remove the specimen. 

4.  Turn the large brass thumbscrew located under the unit counter-clockwise. 

5.  Slide the whole unit off the T-slot bed. 

6.  Recap the top power socket if not in use. 

CAUTION

!

 

Equipment Damage. If the IsoMet unit is not powered off when the Specimen Position 
System power cable is disconnected, the SPECIMEN QUANTITY and DATUM parameter 
values will become inaccurate. 

To reset the SPECIMEN QUANTITY and DATUM parameter values, change SPECIMEN 
QUANTITY to 1 and DATUM to OFF. 

Summary of Contents for IsoMet 5000













































































Reviews:

No comments