Buckleys PST-100 Instruction Manual Download Page 7

PST-100 

In a reasonably ventilated room of a volume greater than 40m

3

, the exposure to 

ozone produced by the high voltage spark should not present a risk to health. In a 

‘confined space’ situation it is likely that ozone levels will exceed the exposure limit 

and present some risk to health. Under these conditions adequate ventilation must 

be provided. 

 

 

 

 

Misuse or failure to comply with the guidelines outlined in this manual may impair 

the safety provided by the equipment. 

PST-100 Earth Terminal 

The PST-100 has been tested and verified by an authorised, independent third 

party as meeting the requirements of IEC 61010:2010 

- Safety requirements for 

electrical equipment for measurement, control, and laboratory use. 
The construction methods employed throughout comply with double insulation. 

The earth terminal located on the handle is a functional earth terminal, NOT a 

Protective Conductor Terminal as defined by IEC61010 and is intended as a high 

voltage return point during the operation of the PST-100. This arrangement also aids 

suppr

ession of possible EMC interference.

 

Therefore when conducting an electrical safety test (Portable Appliance Test) to 

the PST-100 it should be considered a class 2 appliance and tested accordingly. 
 
 

WARNING: 

This equipment must not be used in any combustible 

atmosphere; the high voltage discharge will cause a spark from which 

an explosion could result. 

WARNING: 

This equipment must not be exposed to damp or wet conditions, or 

where the amount of conductive dust is greater than would occur in a normal 

situation 

WARNING: 

Never connect or disconnect the electrode with the PST-100 

connected to the mains supply. 

IMPORTANT: 

We strongly advise that individuals with pacemakers, cochlear 

implants or trans-dermal electronic implants - e.g. glucose monitors do not use 

our high-voltage test equipment under any circumstances. 

Summary of Contents for PST-100

















Reviews: