BSR Whac-a-Mole Owner'S Manual Download Page 38

Page: 38 / 83

Bob's Space Racers

Whac-A-Mole

Arcade Games

TROUBLESHOOTING: 2400 ELECTRONICS

PROBLEMS/CAUSES

PROBLEMS WITH BEACON
Beacon Light Works, but the Disk Does
Not Revolve

Reflector is Slipping

Beacon Light Does Not Work, but the
Disk is Revolving

Bad Bulb

Beacon Does Not Work At All

No Power

Bad Wire Connection(s)

Bad Relay

PROBLEMS WITH THE BELL
Bell Does Not Work At All

No Power

Bad Relay

SUGGESTED FIX

Check the motor to see if it is slipping

adjust if necessary.  There is a tension wheel
that  pushes  an  o-ring  (found  around  the
disk)  tight  to  the  motor  shaft.   Adjust  if the
tension  wheel  is  not  pushing  down  hard
enough on the o-ring.

Check bulb and replace if necessary.

If  the  bell  is  not  working,  then  the  problem
is in a board.   Check voltage to relay board
(12V DC).

If the bell is working, then check all wiring
to and from the beacon.

Check relay on relay board for proper
operation.

Check voltage to relay board (12V DC).
Check wiring.

Swap relay with another one, if problem
follows, then replace bad one.

Summary of Contents for Whac-a-Mole




















































































Search results

Summary of Contents for Whac-a-Mole

Reviews:

Related manuals for Whac-a-Mole

Brands by name

Popular brands

BSR Whac-a-Mole, Owner'S Manual

Search results

Summary of Contents for Whac-a-Mole

Reviews:

Related manuals for Whac-a-Mole

Brands by name

Popular brands