Bryant 569J Series Installation, Start-Up And Service Instructions Manual Download Page 39

Page: 39 / 56

All Units

If either the Low Pressure Switch or High Pressure Switch

opens while thermostat output Y1 or Y2 remain energized,

the compressor contactor is de-energized, the compressor

stops and liquid line solenoid is de-energized (valve

closes). CADM initiates a TRIP event (cooling demand

sensed at CADM terminal Y but no current is measured at

T1, T2, T3 motor sensors); CADM relay opens and RED

LED is illuminated. TRIP condition maintains lockout of

compressor operation until CADM is manually reset.

Reset CADM by cycling unit main power.

Complete system shutdown may be caused by loss of

main power, open compressor internal overload, open

low-pressure or high-pressure switch, or a fault detected

by the CADM logic. Compressor operation without

cooling may indicate the compressor’s ASTP feature is

active; disconnect unit power and allow compressor to

cool. See Service section for further details.

Cooling, Unit With Economizer —

Refer to fan coil unit installation instructions and

economizer

accessory

installation

instructions

for

operating sequences when system is equipped with

accessory economizer.

Heating —

Refer to fan coil unit installation instructions and accessory

heating device installation instructions for operating

sequences in heating mode.

ROUTINE SYSTEM MAINTENANCE

These items should be part of a routine maintenance

program, to be checked every month or two, until a specific

schedule for each can be identified for this installation:

Quarterly Inspection (and 30 days after initial start) —

Indoor section

Condenser coil cleanliness checked.

Return air filter replacement

Outdoor hood inlet filters cleaned

Belt tension checked

Belt condition checked

Pulley alignment checked

Fan shaft bearing locking collar tightness checked

Condensate drain checked

Seasonal Maintenance —

These items should be checked at the beginning of each

season (or more often if local conditions and usage patterns

dictate):

Air Conditioning

Condenser fan motor mounting bolts tightness

Compressor mounting bolts

Condenser fan blade positioning

Control box cleanliness and wiring condition

Wire terminal tightness

Refrigerant charge level

Evaporator coil cleaning

Evaporator blower motor amperage

Heating

Power wire connections

Fuses ready

Manual-reset limit switch is closed

Economizer or Outside Air Damper

Inlet filters condition

Check damper travel (economizer)

Check gear and dampers for debris and dirt

SERVICE

Refrigeration System

EQUIPMENT DAMAGE HAZARD

Failure to follow this caution may result in damage to

equipment.
This system uses Puron

refrigerant which has higher

pressures than R-22 and other refrigerants. No other

refrigerant may be used in this system. Gage set,

hoses, and recovery system must be designed to

handle Puron. If you are unsure consult the equipment

manufacturer.

CAUTION

Compressor Oil —

EQUIPMENT DAMAGE HAZARD

Failure to follow this caution may result in damage to

equipment.
The compressor in a Puron system uses a polyolester

(POE) oil. This oil is extremely hygroscopic, meaning

it absorbs water readily. POE oils can absorb 15 times

as much water as other oils designed for HCFC and

CFC refrigerants. Take all necessary precautions to

avoid exposure of the oil to the atmosphere.

CAUTION

Servicing Systems on Roofs With Synthetic Materials —

POE (polyolester) compressor lubricants are known to cause

long term damage to some synthetic roofing materials.

Exposure, even if immediately cleaned up, may cause

embrittlement (leading to cracking) to occur in one year or

more. When performing any service which may risk

exposure of compressor oil to the roof, take appropriate

569J

Summary of Contents for 569J Series

























































Search results

Summary of Contents for 569J Series

Reviews:

Related manuals for 569J Series

Brands by name

Popular brands

Bryant 569J Series, Installation, Start-Up And Service Instructions Manual

Search results

Summary of Contents for 569J Series

Reviews:

Related manuals for 569J Series

Brands by name

Popular brands