Bryant 105A Installation Instructions Manual Download Page 10

Page: 10 / 10

PURON

(R--410A) REFRIGERANT QUICK REFERENCE GUIDE

Puron refrigerant operates at 50--70 percent higher pressures than R--22. Be sure that servicing equipment and replacement

components are designed to operate with Puron refrigerant

Puron refrigerant cylinders are rose colored.

Recovery cylinder service pressure rating must be 400 psig, DOT 4BA400 or DOT BW400.

Puron refrigerant systems should be charged with liquid refrigerant. Use a commercial type metering device in the manifold hose

when charging into suction line with compressor operating

Manifold sets should be 700 psig high side and 180 psig low side with 550 psig low--side retard.

Use hoses with 700 psig service pressure rating.

Leak detectors should be designed to detect HFC refrigerant.

Puron refrigerant, as with other HFCs, is only compatible with POE oils.

Vacuum pumps will not remove moisture from oil.

Do not use liquid--line filter driers with rated working pressures less than 600 psig.

Do not leave Puron suction line filter driers in line longer than 72 hours.

Do not install a suction--line filter drier in liquid line.

POE oils absorb moisture rapidly. Do not expose oil to atmosphere.

POE oils may cause damage to certain plastics and roofing materials.

Wrap all filter driers and service valves with wet cloth when brazing.

A factory approved liquid--line filter drier is required on every unit.

Do NOT use an R--22 TXV.

If indoor unit is equipped with an R--22 TXV or piston metering device, it must be changed to a hard shutoff Puron TXV.

Never open system to atmosphere while it is under a vacuum.

When system must be opened for service, recover refrigerant, evacuate then break vacuum with dry nitrogen and replace filter driers.

Evacuate to 500 microns prior to recharging.

Do not vent Puron refrigerant into the atmosphere.

Do not use capillary tube coils.

Observe all

warnings

cautions

, and

bold

text.

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Bryant Heating & Cooling Systems 7310 W. Morris St. Indianapolis, IN 46231

Edition Date: 09/15

Replaces: II114CNA--- 02

Catalog No. II114CNA---CNC---03

Summary of Contents for 105A











Search results

Summary of Contents for 105A

Reviews:

Related manuals for 105A

Brands by name

Popular brands

Bryant 105A, Installation Instructions Manual

Search results

Summary of Contents for 105A

Reviews:

Related manuals for 105A

Brands by name

Popular brands