background image

3

1 SAFETY AND WARNING INFORMATION 

GENERAL. 

The correct and safe operation of the unit implies it’s proper and professional transport, storage, assembly  

     

and careful operation and maintenance. 

HANDLE WITH CARE. 

 Do not drop. 

     

                      Disconnect power and communication cables before moving.

WARNING!  

Do not put any body parts into the openings on the side of the device!

WARNING!

  Keep the pedal area clear when power is applied. Wait until init- sequence is finished (no moving) 

 

     

before touching the pedals.

WARNING!

  The CLS-E rudder is not a toy. Small children under 16 years should not operate the rudder without supervision 

     

of an adult. Depending on the settings, or in case of failure, axis can move in any direction and without warnings.

WARNING!

  Do not remove cover, the unit must not be operated without cover (protective hoods)!

WARNING!

  Operation without a permanently  installed pedal is not allowed!

WARNING!

  The unit must be mounted securely on a flat stable surface before operating! 

POWER SUPPLY WARNING!   

Caution electric shock/fire hazard! 

 

     

 

          Do not use any other power supply, as the one supplied by BRUNNER, with your CLS-E rudder.

WARNING ENVIRONMENT!

   For indoor use only. Do not expose to moisture, liquid, or heat.

NO REPAIR AND OPENING!

  The yoke is designed for lifetime lubrication.

WARNING!

  Do not operate device without proper footwear.

WARNING!

  Before allowing third-person operating the hardware, make sure that this third-person reads, understands  

     

and accepts all warnings.

IMPORTANT ERGONOMIC INFORMATION.

 Long periods of repetitive motion using an improperly set-up workspace,

incorrect body position, and poor work habits may be associated with physical discomfort and injury to nerves, tendons, 

and muscles.  

NON-OBSERVANCE OF THESE INSTRUCTIONS MIGHT RESULT IN FAILURES OR IN CASE OF MALFUNCTIONS IN 

INJURIES OF FEET OR LEGS! 

Summary of Contents for CLS-E RUDDER













Reviews: