background image

Operating instructions 

 

General requirements 

Please note that national and local provisions must be satisfied when installing the 

BRULA basic stove firebox. 

Please consult your competent district master chimney sweep about this prior to 

installation. 

He will advise you on the suitable chimney as well as all other requirements which 

are of relevance for the setup and commissioning of your basic stove. A sufficient 

combustion air supply must be ensured in particular, especially with a well sealed 

building shell, flat ventilation systems etc. in order to guarantee smooth operation. 

Your chimney sweep will be able to help here too. He will also check that the 

fireplace has been connected properly. 

The basic stove firebox described here is tested in accordance with EN 13229:2005-

10 taking into account the agreement as per Art. 15a B-VG (since 01.01.2015 in 

Austria only nominal load operation is permitted!). 

It may be attached to a chimney with multiple connections provided that the 

chimney's technical conditions allow this. 

If the basic stove is attached to a chimney with multiple connections, the heating door 

used must be self-closing. This ensures that the door closes automatically after 

adding more fuel and thus the supply pressure of the chimney is not affected. 

Installation site / fire protection regulations 

When setting up the small basic stove, the valid fire protection regulations of the 

German Fire Code Ordinance (FeuVo) must be observed. The specified minimum 

distances to combustible objects and walls must be maintained and the flooring must 

also be protected. 

Note on setting up the fireplace only on surfaces with a sufficient load bearing 

capacity. If the load bearing capacity is not sufficient, suitable measures must be 

taken (e.g., plate for load distribution) to remedy this. 

Caution: 

Thermal insulation / insulation design must be realised as per the specialist 

regulations of the stove and air heating construction trade (TROL) and the country-

specific provisions.

 

 

 

Summary of Contents for B


















Reviews: