Brother MFC-4820C User Manual Download Page 126

Page: 126 / 361

9 - 5

TAD (TELEPHONE ANSWERING DEVICE)

Playing voice messages

Follow the steps below to listen to voice messages:

Press

Play

Adjust the Volume by pressing

All messages are played in the order they were recorded. The
LCD shows the number of the current message, and the total
number of messages.

Press

(RWD) at the end of the message to repeat a

message. Press

(FWD) to skip to the next message. You can

press

and

repeatedly until you reach the message you

want to play.

Press

Stop/Exit

Printing a Fax Message

Once you print a new fax message stored in memory, it is erased
from the memory automatically.

Press

Play

. After two seconds, the fax machine begins to play

voice messages.

If the Fax Storage is set to

and

there are fax messages in memory,
the LCD shows:

To print the faxes, press

—

Press

to exit without printing.

PRINT FAX?
1.YES 2.NO

Summary of Contents for MFC-4820C










































































































































































































































































































































































Search results

Summary of Contents for MFC-4820C

Reviews:

Brands by name

Popular brands

Brother MFC-4820C, User Manual

Search results

Summary of Contents for MFC-4820C

Reviews:

Brands by name

Popular brands