Brother HL-6050DN User Manual Download

Page: 84 / 181

CONTROL PANEL 3 - 13

Control Panel LCD menu

■

Standard paper tray: TRAY 1

■

Multi-purpose tray: MP TRAY

■

Optional lower tray: TRAY 2

There are eight menus. For more information about the selections available in each menu, please see
the pages listed below.

■

INFORMATION

See INFORMATION on page 3-14.

■

PAPER

See PAPER on page 3-15.

■

QUALITY

see QUALITY on page 3-15.

■

SETUP

See SETUP on page 3-16.

■

PRINT MENU

See PRINT MENU on page 3-17.

■

NETWORK

See NETWORK (only on a Network) on page 3-20.

■

INTERFACE

See INTERFACE on page 3-21.

■

RESET MENU

See RESET MENU on page 3-21.

The control panel LCD names for the paper trays are as follows.

Summary of Contents for HL-6050DN






















































































































































































Search results

Summary of Contents for HL-6050DN

Reviews:

Related manuals for HL-6050DN

Brands by name

Popular brands

Brother HL-6050DN, User Manual

Search results

Summary of Contents for HL-6050DN

Reviews:

Related manuals for HL-6050DN

Brands by name

Popular brands