manualshive.com logo in svg

Brother HL-6050DN, User Manual

Share
Download
Brother HL-6050DN User Manual Download Page 9

1 - 1   ABOUT THIS PRINTER

1

What is in the box?

When you unpack the printer, check to see that you have all of the following parts.

1

Printer

2

Drum unit assembly
(with toner cartridge included)

3

Quick setup guide

4

CD-ROM

5

AC power cord

Components may differ from one 
country to another.

Figure 1-1

Interface cable

■

An interface cable is not a standard accessory.

■

Some computers have a USB and a parallel port. Please buy the appropriate cable for the interface 
you intend to use.

■

Most parallel cables support bi-directional communication, but some might have an incompatible pin 
assignment or may not be IEEE 1284-compliant.

■

It is recommended to use a parallel interface cable or USB interface cable that is no longer than 2 
meters (6 feet).

■

When you use a USB cable, make sure that you connect it to the USB connector of your PC.

■

Please make sure that you use a Hi-Speed USB 2.0 certified cable if your computer uses a Hi-Speed 
USB 2.0 interface.

■

Do not connect the USB cable to a non-powered hub or a Macintosh

®

 keyboard.

About this printer

The power cord may be slightly different than the one shown in the Figure 1-1, depending on which 
country the printer was bought in.

1

2

3

4

5

Summary of Contents for HL-6050DN






















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands