Brother HL-4200CN Service Manual Download Page 125 | Manualshive

Page: 125 / 366

background image

- IV-7 -

2.

DISASSEMBLY PROCEDURE

2.1

Precautions

Note:

Parts are controlled as spare parts. When servicing for parts for which no procedures
are described, observe their assembling condition before starting the service.

Note:

For optional parts, refer to the manual for them.

Note:

Though the optional parts are assumed to be removed, they may not be removed if not
required for the purpose of service operation.

WARNING

When performing service operation for parts around the fuser ASSY, start the service
after the fuser ASSY and parts around it have cooled down.

WARNING

Do not use force to prevent damage to parts.

WARNING

Since a wide variety of screws are used, be careful not to mistake their positions, to
prevent the screw holes.

WARNING

Wear a wrist band or the like as far as possible to remove static electricity of the
human body.

♦

Turn the power OFF and remove the power cord from the electric outlet.

♦

Remove the drum unit before starting the disassembling process.

♦

Remove the transfer unit as necessary, and perform disassembly process.

♦

Remove the fuser unit.

♦

Remove the toner cartridges.

♦

Remove the paper cassette from the printer.

♦

Remove the controller board from the printer.

«
...
123
124
125
126
127
...
»

Summary of Contents for HL-4200CN















































































































































































































































































































































































Reviews:

No comments

Related manuals for HL-4200CN

Pixma MG2400 Series

Brand: Canon Pages: 2

ColorPASS-Z5000

Brand: Canon Pages: 130

Brand: Canon Pages: 30

Brand: Canon Pages: 58

image Prograf iPF680 Series

Brand: Canon Pages: 132

Brand: Canon Pages: 44

imageClass LBP6230dw

Brand: Canon Pages: 16

Brand: Canon Pages: 2

imageprograf IPF785

Brand: Canon Pages: 42

Brand: Canon Pages: 148

Color Bubble Jet BJC-8200

Brand: Canon Pages: 6

Color Bubble Jet BJC-1000 Series

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Color Bubble Jet BJC-8200

Brand: Canon Pages: 105

Brand: Canon Pages: 2

Brand: Canon Pages: 68

Brand: Canon Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands