Brother HL-4200CN Service Manual Download Page 265

Page: 265 / 366

V-59

DIAGNOSIS FOR STANDALONE PRINTER

5.1

General

The test print can be taken place on the standalone printer for operation check.

For this purpose, the test print pattern stored in the printer is printed continuously at the

continuous printing speed.

5.2

Printing Method

1. Remove the ESS PWB.

2. Load paper, and turn the power ON.

WARNING

In the following steps, never touch the live parts and driving parts.

3. Short two pins of the test print connector (P31) on the MCU HL-4200.

Reference:

To short two pins, make the screwdriver tip touch the two pins.

4. The printer transits to the READY mode, and starts the printing. (Printing is carried

out continuously in the Duplex mode).

5. To stop the printing, remove the screwdriver to release the short of two pins.

Note:

The paper is fed from the tray 1, and if no paper is loaded in the tray 1, printing is
not carried out.

Reference:

Printing will not start, if the printer is in an error status.

P31

2Pin

1Pin

P14

Fig.5-8

Summary of Contents for HL-4200CN















































































































































































































































































































































































Search results

Summary of Contents for HL-4200CN

Reviews:

Related manuals for HL-4200CN

Brands by name

Popular brands

Brother HL-4200CN, Service Manual

Search results

Summary of Contents for HL-4200CN

Reviews:

Related manuals for HL-4200CN

Brands by name

Popular brands