Brother HE-800A Service Manual Download Page 24 | Manualshive

Page: 24 / 162

background image

1. MECHANICAL DESCRIPTIONS

HE-800A

16

1-11. Lower thread trimmer mechanism

1. When the pulse motor (1) operates, the gear (2) that is installed to the pulse motor shaft engages with the

presser driving arm (3) so that the guide bracket (4) moves along the guide shaft (5) and moves the presser
driving arm (3) in the direction of the arrow.

2. The presser driving arm (3) causes the presser foot lifter connecting rod (6) to move in the direction of the

arrow.

3. The presser foot lifter connecting rod (6) is connected to the lower thread trimmer cam lever (7), so that the

lower thread trimmer cam lever (7) moves.

4. The roller (8) that is installed to the end of the lower thread trimmer cam lever (7) is linked to the cam groove in

the lower thread trimmer cam (9), so that when the lower thread trimmer cam lever (7) operates, the lower
thread trimmer cam (9) moves with it and the movement is transmitted to the lower thread trimmer cam
connecting rod (10) that is connected to the lower thread trimmer cam (9).

4065Q

«
...
22
23
24
25
26
...
»

Summary of Contents for HE-800A



































































































































































Reviews:

No comments

Related manuals for HE-800A

Brand: Quill Falcon Pages: 40

Brand: Bartell Pages: 30

Brand: Necchi Pages: 122

Brand: Singer Pages: 8

Professional 14U12

Brand: Singer Pages: 24

Brand: C.P.Bourg Pages: 142

Brand: Singer Pages: 10

Brand: Aficio Pages: 300

memory craft 5700

Brand: Janome Pages: 62

PerfectCool Cielo

Brand: IDROBASE Pages: 16

Union Special 36200L220-60

Brand: JUKI Pages: 56

Brand: Janome Pages: 43

Brand: ELNA Pages: 48

Brand: JUKI Pages: 120

Brand: WOLFF Pages: 36

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands