Brother Industries SUPER ACE+e Service Manual Download Page 42 | Manualshive

Page: 42 / 56

background image

-40-

17.

FEED ADJUSTMENT (VERTICAL FEED)

STANDARD

Adjustment of the pattern should be possible in test mode "3".

ADJUSTMENT

1.

Loosen the screw securing the pulse motor.

2.

Rotate the pulse motor and adjust the pattern.
* Make sure not to contact the main PC board during the adjustment.
* Install presser foot N before the adjustment.

3.

Tighten the screw securing the pulse motor.

Adjustment Points

* If the pulse motor position is to be adjusted (when the screw is to be turned or the motor is to be moved),

turn off the power to the sewing machine in order to reduce the risk of a short-circuit (or damage) to the
main PC board with the screwdriver.

1.

If the pattern is open as shown by (B), move the pulse motor slightly backward.

2.

If the pattern is overlapping as shown by (A), move the pulse motor slightly forward.

A

B

www.promelectroavtomat.ru

«
...
40
41
42
43
44
...
»

Summary of Contents for SUPER ACE+e

























































Reviews:

No comments

Related manuals for SUPER ACE+e

Brand: DURKOPP ADLER Pages: 46

Brand: GBC Pages: 10

Jem Platinum 720

Brand: Janome Pages: 41

Firebase SG-Z1200

Brand: FROGGYS FOG Pages: 6

Brand: Singer Pages: 34

Brand: Malanbao Pages: 6

Brand: Singer Pages: 39

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 11

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 19

Brand: Panasonic Pages: 40

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands