Brooks MT3809G Metal Tube, Supplemental Manual

Page: 16 / 52

5-2
Section 5 Transducer Blocks
Installation and Operation Manual
X-DPT-FF-MT3809G-Alarms-eng
Part Number: 541B218AAG
December, 2017 Model MT3809G F
OUNDATION
TM
Fieldbus
Index Sub Index
Parameter Name Description
Data Type
Valid Values
Initialized
Value
Read only or Read/W
rite
Table 5-1
Parameters of the Analog Input Transducer Block (continued)
5 4 MODE_BLK.NORMAL
Setting for which mode should be used when operated
with normal conditions
Bit String
x None
x OOS
x
Auto
Auto
Read/
Write
6 BLOCK_ERR Error status of this block Bit String
x None
x Out of Service
None Read
7 UPDATE_EVT On a change in the static data this alert is generated
7 1
UPDATE_EVT.
UNACKNOWLEDGED
Interface to acknowledge this update alert U8
(0) Uninitialized
(1) Acknowledged
(2) Unacknowledged
(0) Uninitialized
Read/
Write
7 2
UPDATE_EVT.
UPDATE_STATE
Indication if the alert has been reported U8
(0) Uninitialized
(1) Reported
(2) Not Reported
(0) Uninitialized Read
7 3
UPDATE_EVT.
TIMESTAMP
The time stamp when the alert is generated TM MM/DD/YY HH:MM:SS 0 Read
7 4
UPDATE_EVT.
STATIC_REVISION
The static revision when the alert was generated. U16 0 to 65535 0 Read
7 5
UPDATE_EVT.
RELATIVE_INDEX The index of the static parameter whose causes this
alert to be generated
U16 0 to 65535 0 Read
8 BLOCK_ALARM
The block alarm can generate an alarm if a block error
occurs
8 1
BLOCK_ALARM.
UNACKNOWLEDGED
Interface to acknowledge this block alarm U8
(0) Uninitialized
(1) Acknowledged
(2) Unacknowledged
(0) Uninitialized
Read/
Write
8 2
BLOCK_ALARM.
ALARM_STATE
Indication if alarm is active or cleared and reported U8
Uninitialized
Clear-Reported
Clear-Not Reported
Active-Reported
Active-Not Reported
Uninitialized Read
8 3
BLOCK_ALARM.
TIMESTAMP
The time stamp when the alarm is generated TM MM/DD/YY HH:MM:SS 0 Read
8 4
BLOCK_ALARM.
SUBCODE
The sub code which causes the block alarm U8
Other
OutOfService
Other Read
8 5 BLOCK_ALARM.VALUE The value of the parameter associated with this alarm U8 0 to 255 0 Read
9
TRANSDUCER_
DIRECTORY A directory that specifies the number of the data
collections in the transducer block
U16 0 0 Read
10
TRANSDUCER_
TYPE
Identifies the transducer error that follows U16 Other (65535) Other Read
11 XD_ERROR Transducer error code U8
Unspecified error
General error
(0) No error
0 Read
12
COLLECTION_
DIRECTORY A directory that specifies the number of the data
collections in each transducer within a transducer block
U8 0 0 Read
13 PRIMARY_VALUE The measure flow value and status.
13 1
PRIMARY_VALUE.
STATUS
The status of the primary value U8
Bad
Good_NonCascade Good Non
Cascade
Read
13 2
PRIMARY_VALUE.
VALUE
The value of the primary value Float 0.0 Read
14 FLOW_RATE_UOM
Units of measurement of the flow rate given in the
primary value
U16 Supported UOMs
Calibrated
value Read/
Write
15 SW_REV Software version of the application
Visible
String x.x.x where the x
represents the version
Read
16 HW_REV Hardware revision of the transmitter
Visible
String x.x.x where the x
represents the version
Read
17 BROOKS_PASSWORD Password protection for manufacture settings
Visible
string
Brooks password ***************
Read/
Write
18 MESSAGE
Extra message field for indicating the transmitter. This
value is not processed Visible
String ASCII
Max 24 chars
Blank
Read/
Write
19 TAG_NAME
Extra tag name for the device. This value is not
processed Visible
String ASCII
Max 16 chars Calibrated
value Read/
Write
20 DESCRIPTOR
Extra descriptor field for the device. This value is not
processed Visible
String ASCII
Max 17 chars
Blank
Read/
Write
21 DEV_DATE Date of calibration
Visible
String
DD/MM/YY
Calibrated
value Read/
Write
22 AO_FILTER The analog filter values used for the flow calculation Float 0.00 to 10.00
Calibrated
value Read/
Write
23 FIN_ASSY_NUM Final assembly number U32 0 to 4294967296
Calibrated
value Read/
Write
24
0..
9
CALIB_POSITION 10 position array with calibrated float positions. Float
Calibrated
values Read/
Write
25
0..
9
CALIB_FLOW_RATE
10 position array with calibrated flow rates according to
the scale
Float
Calibrated
values Read/
Write
26 LFCUTOFF
Low flow cut off value. Every value below this flow will be
cut off to zero
Float 0.00 to 99999.9 0
Read/
Write
27 DENSITY Density uom and value used for the calculation
27 1 DENSITY.UOM U16 Reserved, do not use 0
Read/
Write
27 2 DENSITY.VALUE Float Reserved, do not use 1.0
Read/
Write
28 PRESSURE Pressure uom and value used for the calculation
28 1 PRESSURE.UOM U16 Reserved, do not use 0
Read/
Write
28 2 PRESSURE.VALUE Float Reserved. Do not use 0.0
Read/
Write
Table continued on next page.