manualshive.com logo in svg

BRONKHORST Mini CORI-FLOW MI Series, Instruction Manual

The BRONKHORST Mini CORI-FLOW MI Series offers precise measurement and control of mass flow rate for various gases. Unlock its full potential by downloading the comprehensive Instruction Manual for free from our website. Discover step-by-step guidelines and valuable insights to optimize your experience with this exceptional product.

Share
Download
background image

Bronkhorst®

Instruction Manual MI Series Industrial mini CORI-FLOW™

9.17.120A

33

Alarm Maximum Limit

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned int

RW

0…32000

116

97/1

0x0C21/3106

Maximum limit for 

Measure

 to activate the maximum alarm situation (after 

Alarm Delay Time

). Range 0…32000 represents 0…

100% signal. 

Alarm Maximum Limit

 must be greater than 

Alarm Minimum Limit

.

Default value: 0.

Alarm Minimum Limit

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned int

RW

0…32000

117

97/2

0x0C22/3107

Minimum limit for 

Measure

 to activate the minimum alarm situation (after 

Alarm Delay Time

). Range 0…32000 represents 0…

100% signal. 

Alarm Minimum Limit

 must be smaller than 

Alarm Maximum Limit

.

Default value: 0.

Alarm Setpoint Mode

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

RW

0…1

120

97/5

0x0C25/3110

Specifies whether or not to change the setpoint after an alarm situation is activated.

Value

Description

0

No setpoint change (default)

1

Change setpoint to 

Alarm new setpoint

Alarm New Setpoint

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned int

RW

0…32000

121

97/6

0x0C26/3111

New (safe) setpoint during an alarm until reset. Range 0…32000 represents 0…100% setpoint.

Default value: 0

Reset Alarm Enable

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

RW

0…15

156

97/9

0x0C29/3114

Available reset methods for alarms. Up to 4 different methods can be specified; convert the value to binary to see which

methods are enabled.

Default value: 15 (all bits/methods enabled)

The following methods are supported:

Bit

Value

Description

0

1

Multifunctional switch

1

2

Externally (deprecated)

2

4

By parameter 

Reset

3

8

Automatically (when alarm conditions no longer apply)

4.3

Counter

Counter settings are most easily accessible using FlowPlot or FlowView or a Bronkhorst® readout and control unit.

Counter Mode

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

RW

0…2

130

104/8

0x0D08/3337

Summary of Contents for Mini CORI-FLOW MI Series






















































Reviews:

No comments

Related manuals for Mini CORI-FLOW MI Series

Rayrun BR11 Quick Installation Manual preview
BR11
Brand: Rayrun Pages: 2
IDenticard 9000 Series Converting Instructions preview
9000 Series
Brand: IDenticard Pages: 2
3Ware 9000 Series Specification preview
9000 Series
Brand: 3Ware Pages: 2
Nelsen Corporation C Series Programming Manual preview
C Series
Brand: Nelsen Corporation Pages: 16
National Instruments C Series Getting Started preview
C Series
Brand: National Instruments Pages: 34
Warner Electric MCS202-E1 User Manual preview
MCS202-E1
Brand: Warner Electric Pages: 3
iCeeO2 C30 Instruction Manual preview
C30
Brand: iCeeO2 Pages: 7
SABAF 10 Instructions For Use, Maintenance Instructions preview
10
Brand: SABAF Pages: 6
IBM 2702 Information Manual preview
2702
Brand: IBM Pages: 105
Cabletron Systems SmartSwitch 6000 Installation & User Manual preview
SmartSwitch 6000
Brand: Cabletron Systems Pages: 76
HandyTrac Key Control Easy Manual Installation And Operation preview
Key Control
Brand: HandyTrac Pages: 14
TA STA Quick Start Manual preview
STA
Brand: TA Pages: 6
ValvTechnologies V1 Series Installation And Operations Maintenance Manual preview
V1 Series
Brand: ValvTechnologies Pages: 20
National Instruments NI 9514 User Manual preview
NI 9514
Brand: National Instruments Pages: 72
National Instruments NI 9514 Operating Instructions And Specifications preview
NI 9514
Brand: National Instruments Pages: 41
NAPCO MAGNUM ALERT 3000 FIRE ALARM Basic Operating Instructions preview
MAGNUM ALERT 3000 FIRE ALARM
Brand: NAPCO Pages: 2
Hunter 99112 Installation preview
99112
Brand: Hunter Pages: 2
Tektronix 73A-541 User Manual preview
73A-541
Brand: Tektronix Pages: 112

Brands by name

Popular brands

Load more brands