Brocade Communications Systems MLX Series Installation Manual Download Page 127

Page: 127 / 326

Brocade MLX Series and Brocade NetIron XMR Installation Guide

113

53-1004195-02

Installing a Brocade MLX-32 router

DRAFT: BROCADE CONFIDENTIAL

FIGURE 83

Accessing modules by shifting cable bundles

Installing power supplies in a Brocade MLX-32 router

High Touch Current. Earth connection is essential before connecting supply.

Follow these steps to install a power supply in a Brocade MLX-32 router.

Remove the blank power supply faceplate.

Remove the power supply from the packaging.

Insert the power supply into the slot, using the guides on each side of the slot.

Cable bundles

Summary of Contents for MLX Series







































































































































































































































































































































Search results

Summary of Contents for MLX Series

Reviews:

Related manuals for MLX Series

Brands by name

Popular brands

Brocade Communications Systems MLX Series, Installation Manual

Search results

Summary of Contents for MLX Series

Reviews:

Related manuals for MLX Series

Brands by name

Popular brands