Brocade Communications Systems Fabric OS v6.4 Documentation Update Download

Page: 66 / 70

Fabric OS Documentation Updates

53-1002063-09

Documentation updates for Fabric OS v6.4.0 and v6.4.1

4. Enable the ports you disabled in step 1, using the portenable command.

5. Allow the hosts and devices to fully log in to the fabric before starting normal I/O.

Disabling FCFW flows without removing FCFW

If you are running Fabric OS version 6.2.0f, or a later version, you can disable FCFW flows on a
single host without removing FCFW on the port.

1. Verify you are using Fabric OS version 6.2.0f or a later version using the firmwareshow

command.

2. Disable the port on which you want to disable FCFW, using the portdisable command.

3. Enable a non-FCFW zoning configuration to remove and replace the fcacc zone.

4. Enable the port using the portenable command.

5. Allow the hosts and devices to fully log in to the fabric before starting normal I/O.

Summary of Contents for Fabric OS v6.4







































































Search results

Summary of Contents for Fabric OS v6.4

Reviews:

Related manuals for Fabric OS v6.4

Brands by name

Popular brands

Brocade Communications Systems Fabric OS v6.4, Documentation Update

Search results

Summary of Contents for Fabric OS v6.4

Reviews:

Related manuals for Fabric OS v6.4

Brands by name

Popular brands