background image

page 2

IMPORTANT 
SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE

USING THIS APPLIANCE

W

HEN USING AN ELECTRICAL APPLIANCE

BASIC PRECAUTIONS

SHOULD ALWAYS BE FOLLOWED

INCLUDING THE FOLLOWING

:

WARNING

T

O REDUCE THE RISK OF FIRE

ELECTRIC SHOCK OR INJURY

:

1.

Do not use on wet surfaces or outdoors.

2.

Do not vacuum liquids or fine powders (such as drywall dust).

3.

Do not use to pick up flammable or combustible liquids
such as gasoline or use in areas where they may be present.

4.

Do not pick up anything that is burning or smoking, such as
cigarettes, matches, or hot ashes.

5.

Do not allow to be used as a toy. Close attention is 
necessary when used by or near children.

6.

Use only as described in this manual. Use only 
manufacturer's recommended attachments.

7.

Keep hair, loose clothing, fingers and all parts of body
away from openings and moving parts.

8.

Turn off all controls before unplugging.

9.

Use extra care when cleaning on stairs.

10.

Do not handle plug or appliance with wet hands.

11.

Do not use with damaged cord or plug. If appliance is not
working as it should, if it has been dropped, damaged, left 
outdoors, or dropped into water, return it to a Service Center.

12.

Keep your work area well lighted.

13.

Connect to a properly grounded outlet only. See grounding
instructions shown on page 7.

14.

When performing installation, servicing or cleaning the
unit, it is recommended to wear safety glasses and gloves.

CAUTION

1.

Do not put any object into openings. Do not use with any 
opening blocked; keep free of dust, lint, hair and anything
that may reduce air flow.

2.

Ensure air flows freely to both side intake vents and
exhausts unobstructed from top outlet.

3.

Do not use without filter in place.

4.

Do not use to blow leaves or debris.

5.

Do not put any object on the unit.

6.

Do not install the unit horizontally.

7.

Do not use the pail as a wash bucket.

8.

Do not use the pail as a stool.

9.

Avoid picking up sharp objects.

10.

Do not unplug the unit by pulling on cord. To unplug, grasp
the plug, not the cord.

11.

Store your cleaner indoors in a clean, dry area.

12.

Any servicing other than that recommended in this manu-
al should be performed by an authorized service facility.

13.

We recommend that your unit be inspected by a 
specialized technician once a year.

OPERATION

The power unit is located away from the everyday living areas
of your home – usually in the garage, basement, or utility
room. Through a network of strong, lightweight tubing, the
power unit connects to inlets strategically placed throughout
your home. To clean, attach cleaning tools to the system's
hose and insert the hose into an inlet. The system is turned on
by a power switch on the hose. As you vacuum, dirt and dust
is transported to the power unit where it remains in a debris
pail until emptied. 

This electrical appliance has been evaluated by the appropriate
listing agencies and is intended for household use only.

The system status indicator light(s) on the front of the power
unit indicate that the power unit is ready for use. Under normal 
operation, the light(s) will be green. 

(A red light on Broan 

models VX6000C or VX12000C indicates a need to empty
pail. See page 12 for instructions.)

When you are ready to clean, attach the wand and cleaning
tool onto the end of the hose. Open the inlet cover and insert
the end of the hose into the inlet.

For non-switched hoses, inserting the hose automatically
turns on the power unit; removing the hose shuts off the power
unit. Some hoses have switches which can be used to activate
power unit.

NOTE:

The power unit will not turn automatically ON when
the hose is inserted into its own inlet. To turn the
power unit inlet ON, use the rocker switch located on
the side of the power unit.

Use the cleaning tools as you would for any other vacuum
cleaner. Avoid picking up pine needles, coffee sticks, and other
similar objects. These kinds of objects may become lodged in
the hose or tubing.

CAUTION

DO NOT REMOVE either of the TOP red cap plugs
that are glued to the unit. Removing these glued
plugs will damage the unit. Only remove and use
the outlets covered by the green BOTTOM plugs.

Summary of Contents for VX12000C

















Reviews: