broag REMEHA W40-m ECO Installation And Maintenance Instructions Manual Download Page 16 | Manualshive

Page: 16 / 40

background image

16

remeha W40/60-m ECO

6.4.10 User settings
The user can set the following parameters to the
required values.

1. Flow temperature (basic setting 80˚C).

- Press the 'mode'-key until the digit 1. (with dot)

appears in the 'code'-display.

- The set value 8 0 is shown in the temperature

display.

- Now set the required flow temperature, using the

'

▲

'- and '

▼

'-keys.

Code

Description

1.

7 0

Required flow temperature

- Press the 'store'-key to store the new value (value

will blink twice).

- Press the 'mode'-key until the digit without dot

appears in the 'code'-display.

2. Pump switching (basic setting: pump continues to

operate for 5 minutes)
- Press the 'mode'-key until the digit 1. (with dot)

appears in the 'code'-display.

- Press the 'step'-key until the digit 2. appears in the

'code'-display.

- Set the required value, using the '

▲

'- and '

▼

'-keys.

3. D.H.W. setting (basic setting 65˚C). Only with sensor.

- Press the 'mode'-key until the digit 1. (with dot)

appears in the 'code'-display.

- Press the 'step'-key until the digit 3. appears in the

'code'-display.

- Set the required value, using the '

▲

'- and '

▼

'-keys.

Code

Description

2.

0 0

Pump continues to operate for 10 sec.

2.

X X

Pump continues to operate for
1 - 15 min. (example:

X X

= 05)

2.

9 9

Continuous pump operation

- Press the 'store'-key to store the new value (value

will blink twice).

- Press the 'mode'-key until the digit without dot

appears in the 'code'-display.

Code

Description

3.

6 5

required temperature

- Press the 'store'-key to store the new value (value

will blink twice).

- Press the 'reset'-key to return into the operating

mode.

Operation is as follows:
Imagine: the setpoint for D.H.W. temperature has been
preset at 65°C, the D.H.W. cut-in temperature differen-
tial at 5°C, and the maximum flow temperature during
D.H.W. operation at 80°C (factory settings).
The appliance will modulate at the preset maximum flow
temperature during D.H.W. operation, and will shut down
at a D.H.W. temperature of 70°C (preset value +5°C).
The appliance will cut back in at a D.H.W. temperature
of 65°C (preset D.H.W. temperature
+5°C - D.H.W. cut-in temperature differential).
Both the D.H.W. cut-in differential and the maximum flow
temperature during D.H.W. operation can only be set via
the service menu (para. 10.3.9 and 10.3.10).

«
...
14
15
16
17
18
...
»

Summary of Contents for REMEHA W40-m ECO









































Reviews:

No comments

Related manuals for REMEHA W40-m ECO

Brand: A.O. Smith Pages: 48

Brand: A.O. Smith Pages: 83

Brand: A.O. Smith Pages: 74

Brand: A.O. Smith Pages: 54

Brand: A.O. Smith Pages: 16

Brand: A.O. Smith Pages: 28

Brand: A.O. Smith Pages: 8

Senator RFB006 6kW

Brand: Range Pages: 32

Ciao S 20 C.S.I.

Brand: Beretta Pages: 31

ULTRA Ultra-105

Brand: Weil-McLain Pages: 60

Brand: PeerlessBoilers Pages: 43

Brand: Magikitch'n Pages: 23

Brand: Honeywell Pages: 20

Brand: kunzel Pages: 36

Brand: Potterton Pages: 36

Brand: Unical Pages: 28

Brand: Ferroli Pages: 52

VITODENS 200 WB2 Series

Brand: Viessmann Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands