manualshive.com logo in svg

broag REMEHA W40-m ECO, Installation And Maintenance Instructions Manual

Share
Download
broag REMEHA W40-m ECO Installation And Maintenance Instructions Manual Download Page 14

14

remeha W40/60-m ECO

6.4.5  Forced 'HIGH' mode
By pressing the 'mode' and '

▲

' key simultaneously in

operating mode, the appliance will burn at maximum
power.
The flow temperature, however, cannot exceed the pre-
set maximum, in order to protect the appliance and the
installation.
By pressing the '

▲

' and '

▼

' keys simultaneously, the

appliance will return to operating mode, or will switch to
that mode automatically after 15 minutes.

6.4.6  Forced 'LOW' mode
By pressing the 'mode' and '

▼

' key simultaneously in

operating mode, the appliance will burn at minimum
power.
The flow temperature, however, cannot exceed the pre-
set maximum, in order to protect the appliance and the
installation.
By pressing the '

▲

' and '

▼

' keys simultaneously, the

appliance will return to operating mode, or will switch to
that mode automatically after 15 minutes.

6.4.7  Speed mode (half digits)
(On service level for the heating contractor.)
The fan speed can be read in parts in the speed mode.
- Select the service code C  1 2 (see para. 6.4.9).
- Now select the fan speed code, using the 'mode'-key

(half digits).

6.4.4  Read-out mode (with blinking dot)
Various values can be read in the read-out mode.
On user level.
- Select the read-out mode by pressing the 'mode'-key

until 1. (blinking dot) appears in the 'code'-display.

- Now select the required code, using the 'step'-key.

Code

Description

Read-out (example)

1.

Flow temperature

-  8 0  

2.

Return temperature

-  7 0  

3.

D.H.W. temperature

-  6 5  (with sensor)

4.

Outdoor temperature 

-  0 5  (with sensor)

5.

Not applicable

-  4 0

6.

Flow temperature set point

7.

Room thermostat status

-  0     open  1     closed

and air pressure switch status

-     0  open     1  closed

8.

Flow sensor temperature

-  8 0

Code

Description

Example  4900 r/m

Fan speed

-  4 9  hundreds

Fan speed

-  0 0  units

Summary of Contents for REMEHA W40-m ECO









































Reviews:

No comments

Brands by name

Popular brands

Load more brands