Broadcom NetXtreme/NetLink BCM5717 Programmer'S Manual Download Page 123 | Manualshive

Page: 123 / 593

background image

Jumbo Frames

BCM5718 Programmer’s Guide

Broadcom

®

January 29, 2016 • 5718-PG108-R

Page 123

Figure 25: Send Buffer Descriptor

• The Host Address is the 64-bit address where the send buffer is located in host memory.
• The Length[15:0] is the length of the frame or TCP large segment to be transmitted.
• The VLAN TAG[15:0] field is the tag to be inserted in the frame if flags[6] is set to 1.
• The aggregate HDRLEN[7:0] field is the length of the EIP+TCP headers to be replicated in each

segment arising out of a large TCP segment (LSO). (See Flags also.)

• The MSS[13:0] field is the size of the TCP segments into which a LSO segment is to be chopped up into.

Note that it has been increased to hold the value of a jumbo frame size. The Flags field of SBD is shown in

below.

Table 34: Send Buffer Descriptor Flags

Bit #

Flag Name

Flag Description

0

TCP/UDP Checksum Offload

Enable

This bit enables calculation of TCP or UDP checksums for IPv4 and IPv6

transmitted packets. The driver sets this bit only if the packet contained

within a buffer is TCP or UDP over IPv4 or IPv6.

1

IP Checksum Offload Enable This bit enables calculation of the IPv4 layer-3 checksum. This bit is set

only for IPv4 packets. The driver never sets it for IPv6 packets.

2

Packet End

This bit is set for the last send buffer in a packet.

3

Jumbo Frame

Driver must set this bit to 1 if the MTU length of the Send Frame is >

1500B. The MTU length is the Ethernet payload length and excludes

header length (and trailer length).
All BDs belonging to a send packet must configure this bit identically.

4

HDRLEN[2]

The length of the EIP+TCP headers to be replicated in each

segment arising out of a large TCP segment (LSO).

5

Capture Time Stamp

(BCM5719/5720 only)

If this bit is 1, this frame’s launch time shall be captured in the TX Time-

Stamp Register.

6

VLAN TAG

When this bit is set, the controller inserts a VLAN tag in the Ethernet

header. The value for the inserted tag is taken from the VLAN Tag field in

the send BD.

7

Coalesce Now

If this bit is set, a status block with an updated send consumer index is

DMA'd to the host as soon as this buffer's data has been DMA'd from the

host. An interrupt may or may not be generated depending on the present

state of interrupt avoidance mechanisms.

8

CPU Pre-DMA

If this bit is set, the CPU is required to act upon the buffer before the send

data initiator state machine is kicked off. Alternately, if hardware LSO is

enabled and this bit is set in conjunction with CPU post-DMA, then this

buffer is treated as part of an LSO segment to be further segmented by

hardware.

0x4

0x8

0xC

Host Address

0x0

Length[15:0]

HdrLen[1:0]

MSS[13:0]

Flags

VLAN Tag[15:0]

31

15

0

«
...
121
122
123
124
125
...
»

Summary of Contents for NetXtreme/NetLink BCM5717


















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NetXtreme/NetLink BCM5717

Brand: J3C Pages: 2

Brand: WAREMA Pages: 4

sensoCOMFORT VRC 720/3

Brand: Vaillant Pages: 64

DuetPro Carrycot

Brand: Qtus Pages: 52

Brand: Altronix Pages: 8

Brand: nvent Pages: 6

Brand: Smart Vision Pages: 5

Brand: Teledyne Pages: 47

Brand: Western Co Pages: 14

E4KP ENTRYCHECK

Brand: SDC Pages: 6

Brand: Hanma Pages: 3

Brand: Melexis Pages: 13

F-16 FIGHTERSTICK

Brand: CH Products Pages: 3

DYGIZONE GJD910

Brand: GJD Pages: 13

Brand: M-system Pages: 3

FORCE MASTER 2.1

Brand: Malossi Pages: 46

Brand: IGD Pages: 13

Brand: Danfoss Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands