Broadcast Tools tiny TOOLS VAD - 2 Plus Installation And Operation Manual Download Page 17

131 State Street, Sedro-Woolley, WA 98284 • 360.854.9559 • Fax 866.783.9479

Visit us online at www.broadcasttools.com

Copyright © 1989-2008 by Broadcast Tools, Inc. All Rights Reserved.

VAD-2 Plus  

Voice Alarm Dialer

  Two Input Voice Dialer with Silence Sensor and Dual Relay Control

Phone

PGM

Power

Hook

K1

K2

PGM

SS

Temp.

PWR/12VAC

Telco

SS-Mon

K1

NC

K1

CM

K1

NO

ST

1A

ST

1B

+5

VD

C

Gn

d

Ch

s G

nd

PF

+

PF

SS led ON with valid audio
SS led OFF with NO audio
SS led flashes if enabled and in an alarm condition

Optional

Temp Probe

Pwr led ON if powered
Pwr led flashes if PF is enabled and in an alarm condition
Pwr led OFF during a valid DTMF tone
Pwr led OFF in voice record mode.

Hook led ON
when in an off-
hook condition

K1 led ON when
K1 is closed or
energized
 

K2 led ON when
K2 is closed or
energized

PGM led ON when
programming the
VAD-2 Plus

Recessed Program Switch

Voice/Program TT
Telephone Receptacle

Telephone
Line

Silence Sensor (send)
audio to telco level trimmer

12 VAC wall
transformer
receptacle

K2

NC

K2

CM

K2

NO

ST

2A

ST

2B

SS

L

SS

R

GN

D

CL

R–

CL

R+

Summary of Contents for tiny TOOLS VAD - 2 Plus






















Reviews: