ENGLISH
OPERATION MANUAL
BRITEQ
®
4/12
BT-THEATRE 200TW
13. HANGING BRACKET:
with a knob on both sides to fasten the unit in the desired position. You can use the
hole in the center of the bracket to fix a hook or truss clamp.
14. LOCKING CLIP:
The clip is used to keep the barndoor and color frame in place. Push the clip aside to
open it.
15. BARN DOORS:
they facilitate shaping of the beam of light from the fixture, and prevent the distinctive
scatter of light created by the Fresnel lens from spilling into areas where it is not wanted, such as the eyes
of audience members. Just rotate the barndoor leafs in the desired position.
OVERHEAD RIGGING
Important:
The installation must be carried out by qualified service personal only. Improper installation
can result in serious injuries and/or damage to property. Overhead rigging requires extensive
experience! Working load limits should be respected, certified installation materials should be used,
the installed device should be inspected regularly for safety.
•
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
•
Locate the fixture in a well-ventilated spot, far away from any flammable materials and/or liquids. The fixture
must be fixed
at least 50cm
from surrounding walls.
•
The device should be installed out of reach of people and outside areas where persons
may walk by or be seated.
•
Before rigging make sure that the installation area can hold a minimum point load of
10times the device’s weight.
•
Always use a certified safety cable that can hold 12times the weight of the device when
installing the unit. This secondary safety attachment should be installed in a way that
no part of the installation can drop more than 20cm if the main attachment fails.
•
The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
•
Don’t cover any ventilation openings as this may result in overheating.
•
The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
SETUP MENU / HOW TO SETUP
With the setup menu you can fully configure the projector. All settings are preserved when the unit is
disconnected from the mains. Always press the [MENU] button first to enter the setup menu.
DMX ADDR
Used to set the desired DMX-address.
•
Press the ▲/▼buttons until the desired function is showing on the display and confirm with [ENTER].
•
Use ▲/▼buttons to select the desired DMX512 address. The last occupied DMX-address is also shown:
this makes it easier to set the address of the next unit in the chain.
•
Press the [ENTER] button to save the setting.
Note: on RDM-compatible controllers this option can also be remotely set.
CH. MODE
Used to set the desired channel mode.
•
Press the ▲/▼buttons until the desired function is showing on the display and confirm with [ENTER].
•
Use ▲/▼ buttons to select the desired mode:
•
[1CH 8b] :
1 channel mode (8bit dimmer, CCT selected in the setup menu)
•
[2CH 8b] :
2 channel mode (8bit CCT channel)
•
[3CH 16b] :
3 channel mode (16bit CCT channel).
•
[4CH 16bS] :
4 channel mode (16bit CCT channel)
•
[5CH 16bF] :
5 channel mode (16bit function c CCT channel)
•
Press the [ENTER] button to save the setting.
Note: on RDM-compatible controllers this option can also be remotely set.
DIM CURVE
Used to set the dimmer curve of the master dimmer.
•
Press the ▲/▼buttons until the desired function is showing on the display and confirm with [ENTER].
•
Use ▲/▼ buttons to select the desired mode: