Britax Steelcraft STRIDER PLUS Manual Download Page 18 | Manualshive

Page: 18 / 48

background image

18

15. TO FACE THE SEAT IN OPPOSITE DIRECTION.

WARNING: Always remove your child from the Stroller seat before changing seat direction.

A

Refer to section 14 for

removing the seat from the
frame.

B

Refer to section 11 for

fitting the seat to the frame.

STROLLER ASSEMBLY & OPERATION

16. TO ADJUST THE HEAD PILLOW & SHOULDER HARNESS HEIGHT

A

The head pillow height

is adjustable. The harness
shoulder strap height also
moves with the head pillow.

B

Unzip the pocket

located on the rear side of
the Stroller seat to reveal
the head pillow slider.

NOTE: The head pillow has a small height adjusting range for additional comfort.

C

Hold the slider and

squeeze the two buttons
together. Slide up or down
to adjust the head pillow
height as desired, then zip
the pocket closed.

«
...
16
17
18
19
20
...
»

Summary of Contents for Steelcraft STRIDER PLUS

















































Reviews:

No comments

Related manuals for Steelcraft STRIDER PLUS

Brand: Falcon Pages: 3

Brand: OBaby Pages: 47

Brand: Mamas & Papas Pages: 16

Brand: Gardena Pages: 17

Brand: Badger Meter Pages: 16

Brand: ICM Controls Pages: 2

Brand: ICM Controls Pages: 2

Brand: U-Prox Pages: 3

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 340

Brand: ETC Pages: 8

Brand: Riello Pages: 72

Brand: Phoenix Contact Pages: 56

Brand: DirectConnect Pages: 2

Brand: zeeltronic Pages: 15

Brand: M-system Pages: 3

Touch Screen Controller RX142

Brand: 3M Pages: 29

Brand: PXM Pages: 15

Brand: Pro-face Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands