Bristan Quadrato Tap Range Installation Instructions & User Manual Download Page 6

Bidets of this type may:

a.

Be supplied with cold and / or hot water 
through type AA, AB, AD or AUK1 backflow 
prevention arrangement or type DC device 
serving the bidet only. See Diagram 3: or

Type AA, AB, AD or AUK1 air gap with or 

Type AA, AB, AD or AUK1 air gap with or 

Type AA, AB, AD or AUK1 air gap with or 

Type AA, AB, AD or AUK1 air gap with or 
without blended water cistern or type DC 

without blended water cistern or type DC 

without blended water cistern or type DC 

without blended water cistern or type DC 
backflow Prevention device.

backflow Prevention device.

backflow Prevention device.

backflow Prevention device.

b.

Be supplied with cold water from an 
independent distributing pipe serving the 
bidet only, or a common distributing pipe 
serving the bidet and which may also serve 
a WC or urinal flushing cistern at a lower 
level. See Diagram 4; or

c.

Be supplied with hot water from a water heater, which is supplied from an independent 
distributing pipe, that serves the bidet only. See Diagram 4: or

Diverter or 
separate control 
valves to hose or 
ascending spray

Type AA, AB, AD or AUK1 air gap with 
or without blended water cistern or 
Type DC backflow prevention device

Zone of backflow risk

300mm minimum

Hot and 
cold water 
supply or 
distributing 
pipes to 
mixer

Blended cold 
and hot water 
distributing 
pipe

FL

Diagram 3

Diagram 3

Diagram 3

Diagram 3

distributing pipe, that serves the bidet only. See Diagram 4: or

d.

Where the bidet is at a lower elevation than 
any other outlets or appliances, be supplied 
with water from a common cold and / or 
hot water vented distribution pipe providing 
that;

(i)

the elevation of the spillover level of the 
bidet, if there is no flexible hose; or

(ii)

the elevation of the spray outlet, with the 
hose extended vertically above the spill 
over level of the bidet

Whichever is the highest, is not less than 
300mm below the point of connection with the 
distributing pipe which serves over appliances 
or outlets. See Diagram 5.

SgV

WP

Storage cistern with 
Type AG air gap

Hot water 
heater serving 
single bidet only 
(see G15.10c)

FL

DP to serve WC 
or urinal flushing 
cistern only (see 
G15.10b)

Cold water DP to 
other appliances 

Bidet

Diagram 4

Diagram 4

Diagram 4

Diagram 4

06

Summary of Contents for Quadrato Tap Range


















Reviews: