background image

16

1019099-F

English Manual

================================================================================================

MAINTENANCE / SPECIFICATIONS

MAINTENANCE

-  After the first 30 minutes of 

use check all fasteners for 

tightness.

-  Tines are manufactured with galvanized steel to resist 

wear of abrasive soil. Striking objects can cause tines to 

curl or break. Contact our Customer Service Department 

to purchase replacement Tines (Part # 1018833).

-  PREVENTING RUST:  

Aerators are essentially 

maintenance free. However as with any steel product, 

it can rust. Apply a light coat of oil on tines after use to 

prevent rust. For rust appearing on painted surfaces, 

sand lightly and coat with enamel.

-  Periodically remove debris that builds up between tines.

-  Apply lubricating oil at each tine and 

bearing before use.

STORAGE

points facing the wall or ground.

-  Store Aerator on the ground or low to the ground.
-  Do not store Aerator hanging from the wall, ceiling or 

with Tine points facing outward.

-  Product packaging can be used to offer a protective area 

around the Tines.

-  Drawbar is a trip hazard. Avoid leaving Drawbar in aisle 

ways and walking paths.

CAUTION: Avoid Injury!

  Keep body parts away from under drawbar.  

Do not disconnect aerator from the towing vehicle with weight on the tray.

SPECIFICATIONS

Maximum Towing Speed . . . . . . . . . . . . .  5 mph.
Maximum Load . . . . . . . . . . . . . . . . . . .  150 lbs.
Empty Weight . . . . . . . . . . . . . . . . . . . . .  42 lbs.
Maximum Towed Weight  . . . . . . . . . . . .  192 lbs.

CAUTION:

  

AVOID INjURY!

  

-  Store Aerator  

in low traffic  

aisleways.

-  Store Aerator  

with the tine 

The Aerator Tines are very 

sharp. Care should be taken 

when choosing a storage 

location for this product.

OPTIONAL 

ACCESSORY

Magnetic Hitch Pin

MHPK-12BH

This quick-connect magnetic  

hitch pin can replace a regular 

cotter pin for an extra-strong,  

convenient upgrade. 
- Diameter:  1/2” 

- Pin Length:  3” 

NOTE: 

 Additional accesories are also available  

in our Parts Store online:  shop.brinly.com

Summary of Contents for SAT2-40BH-S



















Reviews: