Brinly PA-403BH Owner'S Manual Download Page 2

INDRODUCTION

L-1762-L

2

English Manual

================================================================================================

REQUIRED TOOLS  

FOR ASSEMBLY

============================

•  7/16” Wrench

•  7/16” Socket & Ratchet

•  9/16” Wrench

•  9/16” Socket & Ratchet

•  1/2”  Socket & Ratchet

•  Pliers

•  Gloves

SAFETY LABELS AND NOTATION

=========================================================

This symbol will help to point out important safety  

precautions throughout this manual. It means: 

ATTENTION! 

BECOME ALERT! Your safety is involved.

The safety labels shown in this section are placed in important areas on your 

product to draw attention to potential safety hazards. 
On your product safety labels, the words 

DANGER

WARNING

 and 

CAUTION

 are 

used with the safety-alert symbol. DANGER identifies the most serious hazards.
The  operator’s  manual  also  explains  any  potential  safety  hazards  whenever 

necessary in special safety messages that are identified with the word, 

CAUTION

and the safety-alert symbol.

GENERAL NOTES (OPERATION)

Caution should be taken when towing and/or using any attachment. This attachment 

combined with the weight distribution, turning radius, and speed of towing vehicle 

can result in severe injury or death to operator, damage to towing vehicle, and/or 

attachment if not used properly. Follow all towing safety precautions noted in the 

towing vehicle owner’s manual, including the following precautions:

•  Ensure the combined weight of the towing vehicle (tow vehicle  

operator weight) is greater than the maximum towed weight of attachment 

(empty attachment weight of load).  

•  Do not exceed maximum towing capacity of towing vehicle.

  

 

    

CUSTOMER RESPONSIBILITIES

- Please read & retain this manual. The instructions will enable to assemble and maintain your product properly. 

- Please carefully read and observe the SAFETY 

SEcTION of this manual.

- Follow a regular schedule in maintaining and caring for your Brinly-Hardy product.

CONGRATULATIONS on the purchase of your new Brinly-Hardy Plug Aerator! This accessory has been designed, engineered 

and manufactured to give you the best possible dependability and performance.

Should you experience any problem you cannot easily remedy, please do not hesitate to contact our knowledgeable customer 

service department toll-free at 1-877-728-8224. We have competent, well trained technicians to help you with the assembly and 

use of your Plug Aerator.

TABLE OF CONTENTS

============================

Safety . . . . . . . . . . . . . . . . . 2-3
Specifications  . . . . . . . . . . . . .

4

Hardware Identifier  . . . . . . .

5-6

PA-403BH

 Assembly  . . . . . . . . . . . .

7-14

PA-482BH

 Assembly  . . . . . . . . . . . 15-22

Operation, Maintenance 

and Service 

  . . . . . . . . . . 23-25

Parts List

  . . . . . . . . . . . .

26-27

Limited Warranty   . . . . . . . .

 28

RECORD PURCHASE INFORMATION 

===============================================================

Record your purchase information in the spaces provided below:

DATE OF  

PURCHASE  ��������������������������������������������������

COMPANY NAME   ���������������������������������������������   

SERIAL NUMBER  ���������������������������������������������

CO. PHONE   �������������������������������������������������

Summary of Contents for PA-403BH





























Reviews: