Brightlink BLIP-A300TR-P-P User Manual Download Page 21 | Manualshive

Page: 21 / 51

background image

BRIGHTLINK 4K IP AV DISTRIBUTION

16

5.5 Video Wall Routing Tab

The tab "Video Wall" allows for a single source signal (TX) to be assigned to multiple
Receiver (RX) units and displayed across multiple screens, appearing as a single video
wall. The figure below illustrates the "Video Wall" routing tab inside the IPA Manager.
The top portion is reserved for configuring and setting up the video wall, while the
bottom half lists all available TX (Transmitter) and RX (Receiver) units.

The video wall size can be adjusted by changing the number of rows and columns. The
values for "bezel correction" represent the absolute amount of pixels. The default value
is set to 16 pixels. Increase this value to adjust for thicker bezels while a value of zero
would indicate no bezel correction at all is to be applied.

Note: The source signal must be progressive scan.

«
...
19
20
21
22
23
...
»

Summary of Contents for BLIP-A300TR-P-P




















































Reviews:

No comments

Related manuals for BLIP-A300TR-P-P

THERMASGARD TM 65

Brand: S+S Regeltechnik Pages: 16

PREMASGARD 211 Series

Brand: S+S Regeltechnik Pages: 11

Brand: DAPAudio Pages: 20

XDOM RPL - PRODUCTSHEET

Brand: Ebode Pages: 24

Realvision RV-220P

Brand: Raymarine Pages: 24

Brand: Leica Pages: 32

Brand: Muzak Pages: 3

Brand: Teac Pages: 40

Brand: R.V.R. Elettronica Pages: 52

Brand: LotusRC Pages: 2

Brand: Grundig Pages: 6

Brand: Topfield Pages: 72

Brand: Mun Ah Plastic Electronic Toys Pages: 3

Brand: Naxa Pages: 5

Brand: Icom Pages: 227

Brand: Icom Pages: 108

Brand: JVC Pages: 76

Brand: Crosley Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands