background image

17

Warranty Information

Briggs & Stratton Corporation (B&S), the California Air Resources Board (CARB)

and the United States Environmental Protection Agency (U.S. EPA)

Emissions Control System Warranty Statement 

(Owner’s Defect Warranty Rights and Obligations)

The California Air Resources Board (CARB), U.S. EPA and

B&S are pleased to explain the Emissions Control System

Warranty on your small off-road engine (SORE). In

California, new small off-road engines model year 2006 and

later must be designed, built and equipped to meet the

State’s stringent anti-smog standards.
Elsewhere in the United States, new non-road, spark-ignition

engines certified for model year 1997 and later must meet

similar standards set forth by the U.S. EPA. B&S must

warrant the emissions control system on your engine for the

periods of time listed below, provided there has been no

abuse, neglect or improper maintenance of your small

off-road engine.
Your emissions control system includes parts such as the

carburetor, air cleaner, ignition system, fuel line, muffler and

catalytic converter. Also included may be connectors and

other emissions related assemblies.
Where a warrantable condition exists, B&S will repair your

small off-road engine at no cost to you including diagnosis,

parts and labor.

Briggs & Stratton Emissions Control Defects Warranty Coverage

Small off-road engines are warranted relative to emissions control parts defects for a period of two years, subject to provisions set

forth below. If any covered part on your engine is defective, the part will be repaired or replaced by B&S.

Owner’s Warranty Responsibilities

As the small off-road engine owner, you are responsible for

the performance of the required maintenance listed in your

Operating and Maintenance Instructions. B&S recommends

that you retain all your receipts covering maintenance on

your small off-road engine, but B&S cannot deny warranty

solely for the lack of receipts or for your failure to ensure the

performance of all scheduled maintenance.
As the small off-road engine owner, you should however be

aware that B&S may deny your warranty coverage if your

small off-road engine or a part has failed due to abuse,

neglect, improper maintenance or unapproved

modifications.

You are responsible for presenting your small off-road engine

to an Authorized B&S Service Dealer as soon as a problem

exists.
The undisputed warranty repairs should be completed in a

reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and

responsibilities, you should contact a B&S Service

Representative at 1-414-259-5262.
The emissions warranty is a defects warranty. Defects are

judged on normal engine performance. The warranty is not

related to an in-use emissions test.

Briggs & Stratton Emissions Control Defects Warranty Provisions

The following are specific provisions relative to your Emissions Control Defects Warranty Coverage. It is in addition to the B&S

engine warranty for non-regulated engines found in the Operating and Maintenance Instructions.

1. Warranted Parts

Coverage under this warranty extends only to the parts

listed below (the emissions control systems parts) to the

extent these parts were present on the engine

purchased.

a. Fuel Metering System

Cold start enrichment system

Carburetor and internal parts

Fuel pump

Fuel line, fuel line fittings, clamps

Fuel tank, cap and tether

Carbon canister

b. Air Induction System

Air cleaner

Intake manifold

Purge and vent line

c. Ignition System

Spark plug(s)

Magneto ignition system

d. Catalyst System

Catalytic converter

Exhaust manifold

Air injection system, Pulse valve

e. Miscellaneous Items

Vacuum, temperature, position, time sensitive

valves and switches

Connectors and assemblies

2. Length of Coverage

B&S warrants to the initial owner and each subsequent

purchaser that the Warranted Parts shall be free from

defects in materials and workmanship which caused the

failure of the Warranted Parts for a period of two years

from the date the engine is delivered to a retail purchaser.

3. No Charge

Repair or replacement of any Warranted Part will be

performed at no charge to the owner, including

diagnostic labor which leads to the determination that a

Warranted Part is defective, if the diagnostic work is

performed at an Authorized B&S Service Dealer. For

emissions warranty service contact your nearest

Authorized B&S Service Dealer as listed in the “Yellow

Pages” under “Engines, Gasoline,” “Gasoline Engines,”

“Lawn Mowers,” or similar category.

4. Claims and Coverage Exclusions

Warranty claims shall be filed in accordance with the

provisions of the B&S Engine Warranty Policy. Warranty

coverage shall be excluded for failures of Warranted

Parts which are not original B&S parts or because of

abuse, neglect or improper maintenance as set forth in

the B&S Engine Warranty Policy. B&S is not liable to

cover failures of Warranted Parts caused by the use of

add-on, non-original, or modified parts.

5. Maintenance

Any Warranted Part which is not scheduled for

replacement as required maintenance or which is

scheduled only for regular inspection to the effect of

“repair or replace as necessary” shall be warranted as to

defects for the warranty period. Any Warranted Part which

is scheduled for replacement as required maintenance

shall be warranted as to defects only for the period of time

up to the first scheduled replacement for that part. Any

replacement part that is equivalent in performance and

durability may be used in the performance of any

maintenance or repairs. The owner is responsible for the

performance of all required maintenance, as defined in

the B&S Operating and Maintenance Instructions.

6. Consequential Coverage

Coverage hereunder shall extend to the failure of any

engine components caused by the failure of any

Warranted Part still under warranty.

Summary of Contents for 21000 Series





















Reviews: