Briggs & Stratton 030430 Service And Repair Manual Download Page 26

Page: 26 / 76

BRIGGSandSTRATTON.COM

Oil and Oil Filter Maintenance

Change oil after the ﬁ rst 5 hours of operation. After that,
change oil after every 50 hours of operation. Change oil more
often if engine is operated in dirty or dusty conditions, under
heavy loads, or in high ambient temperatures.

1. Remove oil drain plug from side or bottom of engine

and drain oil while the engine is still warm.

2. Install drain plug.

3. Remove oil ﬁ lter, if equipped.

4. Apply light coat of clean engine oil to new filter gasket.

Screw new ﬁ lter on by hand until gasket contacts ﬁ lter
mounting adapter. Then tighten an additional 1/2 to 3/4
turn.

5. Fill crankcase with the correct amount of new oil.

6. Start engine and run at idle for a minute or so. Shut

engine off and wait for oil to settle back into the
cylinder.

7. Check dipstick. If necessary, add more oil slowly to

bring level to FULL mark on dipstick.

NOTICE:

Do not overﬁ ll. Overﬁ lling can cause seals to fail,

smoke from the exhaust, or overheating due to oil foaming.

8. Replace oil fill cap and dipstick.

9. Start and run engine. Check for oil leaks.

Summary of Contents for 030430













































































Search results

Summary of Contents for 030430

Reviews:

Related manuals for 030430

Brands by name

Popular brands

Briggs & Stratton 030430, Service And Repair Manual

Search results

Summary of Contents for 030430

Reviews:

Related manuals for 030430

Brands by name

Popular brands