8
O
W
N
E
R
'S
M
A
N
U
A
L
•
C
O
N
T
R
O
L
come to a complete stop, then simply lift the running
belt to feel the running deck; if the deck feels dry and
there is very little evidence of lubricant on your hand,
lubricate the running deck according to the following
instructions:
1.
Attach the nozzle of the lubrication tube to the T-
Lube S container.
2.
Lift the running belt and lock it.
3.
Position the nozzle between the belt and the board.
Try to reach the spray as far into the center of the
running deck as possible.
4.
Spray the lubricant for 5 seconds.
5.
Lower the running deck into its normal position.
Let the belt run for at least a minute at 1,5 kph. This is
done to lubricate the belt evenly.
NOTE!
You should let the treadmill run at least five
minutes before lifting the running deck to the storage
position. This will prevent the lubricant from spilling.
NOTE!
Lubricate your treadmill only with T-Lube
S silicon lubricant. Contact your local Tunturi
distributor for further supplies of T-Lube.
ALIGNING THE RUNNING BELT
Monitor belt tracking during exercise and make
adjustments as needed. The belt should run in the
center of the treadmill. Alignment is not usually
needed, provided
•
the treadmill is placed on an even, solid and
horizontal surface and the belt is correctly tensioned
•
the alignment of the belt is correct
It is, however, possible for the belt to be pushed to
one side due to the user’s running style (e.g. more
weight on one foot). The alignment of the belt is
adjusted by turning the two bolts at the back of the
treadmill.
ALIGN THE BELT ACCORDING TO THE FOLLOWING
INSTRUCTIONS:
1.
Turn the power switch on and increase the
treadmill’s speed to 5 km/h (3 mph).
2.
If the belt drifts to the left, turn the left adjustment
bolt 1/4 turn clockwise and the right adjustment bolt
1/8 turn anti-clockwise. If the belt drifts to the right,
turn the right adjustment bolt 1/4 turn clockwise and
the left adjustment bolt ¼ turn anti-clockwise.
3.
If the belt remains centered the adjustment is
correct. If not, continue to make small adjustments
as above until the belt is correctly aligned. If the belt
is allowed run across to one side for long periods of
time the edges of the belt may be damaged and the
treadmill may not continue to operate correctly. Any
damage to the belt caused by the lack of necessary
adjustment will not be covered by the warranty.
ADJUSTING THE BELT TENSION
The belt must be tensioned if it begins to slip on the
rollers. In normal use, however, keep the belt as loose
as possible! The belt tension is adjusted by turning
the same screws as used for aligning the running belt.
If turning the screws will not effect the belt tension,
please contact your local Bremshey dealer.
1.
Increase the treadmill’s speed to 5 km/h (3 mph).
2.
Turn both adjustment screws an equal amount, ¼
turn clockwise.
3.
Try to slow the belt down by holding onto the
handrails and braking as you walk (as if you were
walking downhill). If the belt slips, turn another 1/4
turn and repeat the test. When braking heavily the belt
may slip. If the belt keeps slipping despite repeated
adjustments, please contact your local Bremshey dealer.
MALFUNCTIONS
NOTE!
Despite continuous quality control, defects and
malfunctions caused by individual components may
occur in the equipment. In most cases it’s unnecessary
to take the whole device in for repair, as it’s usually
sufficient to replace the defective part. Always give
the model, serial number of your equipment and in
case of malfunctions also conditions of use, nature of
malfunction and any error code.
When you encounter unusual behavior from the
treadmill, simply turn the power switch off, wait
1 minute and turn the power switch on to reset the
treadmill. This should clear incidental errors and
ready the treadmill for normal operation again. If after
you have reset the treadmill by turning the power
switch off and on again, and the treadmill is still not
operational, contact your local Bremshey dealer for
service.
If you require spare parts, always give the model,
serial number of your equipment and the spare part
number for the part you need. The spare part list
is at the back of this manual. Use only spare parts
mentioned in the spare part list.
ERROR CODES
The user interface will display information about
operational faults.
E1:
Speed sensor error. Unplug the electrical cord
from the wall outlet and from the treadmill, wait
1 minute and turn the power switch on again. If
treadmill recovers to normal operation, you may
continue to use the treadmill. Otherwise, call the
dealer for service.
E6, E7:
Lift motor error. Unplug the electrical cord
from the wall outlet and from the treadmill, wait
1 minute and turn the power switch on again. If
treadmill recovers to normal operation, you may
continue to use the treadmill. Otherwise, call the
dealer for service.
PROTECTIVE CIRCUIT
The machine will shut off when the electricity load is
above the machine’s capacity. To restart the machine,
please follow the procedure below:
A.
Unplug the power cord from the machine’s socket.
B.
Push in the safety switch.
C.
Replug the power cord into the machine’s socket.
Summary of Contents for TREADLINE CONTROL
Page 75: ...75...
