40
Chapter 8: Installing hutch options.
For the Hutch Doors, assembly is identical. Attach door hinge
(2 or 3 hinges per door) by aligning the hinge to the bored
holes and push down. Tighten the top and bottom screws on
the hinge by hand with a screwdriver until snug. Next, align
the hinge with the front side of the hinge plate and push the
back side of the hinge into place. You’ll hear a snap once the
hinge is locked into place. Repeat for opposite hinge and attach door handles. For
Full door, attach middle hinge at bored hole location.
Top, Bottom Or
Full Doors
STEP 7
Now that assembly has been completed, we hope that your
BredaBed will bring you many years of enjoyment! Contact us
if you ever have any questions.
You may notice that you have extra hardware once assembly has been
finished. This is normal, we provide extra hardware with each bed model as
a convenience. Once assembled, you can safely discard this hardware.
The labels/stickers can now be removed from all parts. We
use EZ peel-off labels for quick and residue free removal.
DO NOT remove the warning label on the “Bed Cabinet
Top Nailer”.
The parts can be wiped clean with a damp cloth.
Affix the clear sleeve envelope to the backside of the Bed Face
Panel and store your instructions there for future use.
Finishing
Up
We provide 3 adjustable shelves to be positioned at your
own convenience. Use the shelf pins (4 pins per shelf) from
hardware package #11 at the desired height and place the
shelf on top of the flat portion of the shelf pin.
The side hutches each come with a hanging rod for hanging
clothes to be positioned at your own convenience. Insert 2 closet rod support
brackets from hardware package #18 on the inside, middle of each side hutch.
Once inserted, slide the closet rod down between the brackets (the brackets have
a channel on the bottom for the closet rods to sit in). We recommend keeping ~2
3/4” of clearance above the closet rod.
Shelving And
Hanging Rods
STEP 8
REQUIRED TOOLS
• Cordless Drill with #2 Phillips
• 1/2 Wrench or Adjustable Pliers
• #2 Phillips Screwdriver
ESTIMATED TIME
30 Minutes
Note: This is an average time only,
yours may vary.
Once the Arm Locks are engaged, remove the bolts in Hole #2
(10 ½” from the end of the metal frame) and loosen the bolts
in Hole #3 (19 ¼” from the end of the metal frame).
Rotate the Bed Face Panel outward towards you.
You can now lift the Bed Face Panel off the mechanism arms.
STEP 2
Remove the screws in Bed Cabinet Top Nailer and Bed Cabinet
Bottom Nailer. Lay the Bed Cabinet fl at onto the fl oor and
loosen the cam locks with a #2 Phillips screwdriver. If needed,
the Bed Face Panel can be unscrewed and taken apart. The
holes in the drywall can be patched with drywall putty.
STEP 3
Rotate the Bed Face Panel outward
in order to re-engage the mechanism
Arm Locks. These are found on the
sides bed frame and are near the
mechanism, they are 3” long and have
a partial circle on the end. The Arm
Locks rest against the top corner Hex
nut on the mechanism and are used
to hold the Bed Face Panel outward.
LEFT SIDE (FACE PANEL NOT SHOWN FOR CLARITY)
STEP 1
RECOMMENDED:
For video instructions visit:
breda.us/remove
NEVER REMOVE THE SCREWS IN “BED CABINET TOP NAILER”
FROM THE WALL WITHOUT FIRST REMOVING THE BED FACE PANEL.
THE BED CABINET WILL COLLAPSE OTHERWISE.
DO NOT ATTEMPT TO PRY OFF THE MECHANISM ARM FROM THE
FRAME WHEN THE MECHANISM ARM IS UNDER TENSION. ALWAYS
FOLLOW THE STEPS BELOW IN THE CORRECT ORDER.
