background image

Breckwell 

9

CHIMNEY

Your wood stove may be hooked up with a factory built or masonry chimney, matching the diameter of the stove exhaust. If you 

are using a factory built chimney, it must comply with UL 103 or CSA-B365 standard; therefore it must be a Type HT (2100°F). It 
is extremely important that it be installed according to the manufacturer’s speci

fi

 cations.

If you are using a masonry chimney, it is important that it be built in compliance with the speci

fi

 cations of the National Building 

Code. It must be lined with 

fi

 re clay bricks, metal or clay tiles sealed together with 

fi

 re cement. (Round 

fl

 ues are the most ef

fi

 cient).

The interior diameter of the chimney 

fl

 ue must be identical to the stove smoke exhaust. A 

fl

 ue which is too small may cause draft 

problems, while a large 

fl

 ue favors rapid cooling of the gas, and hence the build-up of creosote and the risk of chimney 

fi

 res. Note 

that it is the chimney and not the stove which creates the draft effect; your stove’s performance is directly dependent on an adequate 
draft from your chimney.

Do not connect this unit to a chimney 

fl

 ue serving another appliance.

The following recommendations may be useful for the installation of your chimney:
• 

It must rise above the roof at least 3’ (0.9m) from the uppermost point of contact.

• 

The exterior portion should be double or triple wall pipe to ensure proper draft.

• 

The chimney must exceed any part of the building or other obstruction within a 10’ (3.04m) distance by a height of 2’ (0.6m).

• 

Installation of an interior chimney is always preferable to an exterior chimney.  The interior chimney will be hotter than an 
exterior chimney that is being cooled by the ambient air outside the house. Therefore the gas which circulates will cool slower, 
thus reducing the build-up of creosote and the risk of chimney 

fi

 res.

• 

The draft caused by the tendency for hot air to rise will be increased with an interior chimney.

• Using 

fi

 re screen at the extremity of the chimney requires regular inspection in order to insure that it is not obstructed thus 

blocking the draft, and it should be cleaned when used regularly. 

Summary of Contents for SW940

























Reviews: