8
9
EN
EN
USING THE ATTACHMENTS
Floor/carpet brush (1)
When using the brush (1) set the switch (2) to the
necessary «FLOOR/CARPET» position (pic. 1).
Combined crevice nozzle (26)
The combined crevice nozzle (26) can be used for
cleaning radiators, crevices or spaces between
cushions, as well as for collecting dust from furniture
surface. The pile on the brush prevents damage of
polished furniture surfaces. While cleaning, set the
brush to the required position.
Furniture/furniture upholstery brush (27)
The attachment (27) is intended for cleaning fabric
surfaces of upholstered furniture and for collecting
dust from furniture surface, the pile on the brush (27)
prevents damage of polished furniture surface. During
operation install the brush on the attachment (27).
ASSEMBLING THE VACUUM CLEANER
Attaching and removing the flexible hose (7)
•
Insert the flexible hose (7) ending (8) into the air inlet
(10) until the locks (9) catch.
•
To remove the flexible hose (7), press the locks (9)
and detach the ending (8) from the air inlet (10).
Attaching the telescopic pipe (4) and the
attachments
•
Attach the telescopic extension pipe (4) to the flexible
hose handle (5).
• Extend the lower part of the telescopic extension
pipe (4) to the required length, having preliminarily
pressed the lock (3) (pic. 2).
•
Choose the necessary attachment: floor/carpet brush
(1), combined crevice nozzle (26) or parquet/laminate
floor attachment (27) - and attach it to the telescopic
extension pipe (4).
• You can attach the combined crevice nozzle (26) to
the flexible hose handle (5).
ATTENTION!
• Do not use the vacuum cleaner in places where
aerosols are used or sprayed and in proximity to
highly inflammable liquids, do not use the vacuum
cleaner in the places where such liquids are stored.
• The vacuum cleaner is not intended for collecting
water or any other liquids; do not use it for collecting
burning or smoking cigarettes or cinders.
• Do not use the vacuum cleaner for collecting dust of
plaster, concrete, flour or ashes.
•
Take sharp objects away from the floor before
cleaning to prevent damage to the unit.
• If the suction power of the vacuum cleaner decreases
rapidly while cleaning, switch it off immediately,
unplug it and check the telescopic pipe (4) or
the flexible hose (7) for obstruction. Remove the
obstruction, after that you can resume cleaning.
USING THE VACUUM CLEANER
The dust bin (11) is equipped with the cyclonic filter (20)
which sieves out garbage and dust from the ingoing air,
and the inlet HEPA (19) filter fully retains the finest dust
particles.
Note:
provide that the HEPA filter (19) is always clean,
because the overall performance of the vacuum cleaner
depends on it.
Attention!
Before switching on and using the vacuum cleaner,
make sure that the HEPA filter (19), the separator (20),
the dust bin (11) and the outlet filter (17) are installed
properly.
• Take the power plug and unwind the power cord to
the required length, connect the power plug to the
mains socket.
• The yellow mark on the power cord indicates the
maximum cord length. Do not pull out the power cord
further than the red mark.
•
Press the on/off button (16) to switch the vacuum
cleaner on.
• While cleaning, you can control the suction power
using the manual suction power control (6) on the
flexible hose handle (5) (pic. 3).
•
After you finish cleaning, switch the vacuum cleaner
off by pressing the on/off button (16) and unplug it.
•
To wind the power cord, press the button (14); keep a
hold of the winding cord with your hand.
• If you have to make a break during the cleaning,
switch the vacuum cleaner off by pressing the button
(16) and install the brush (1) to the brush storage
(15) (pic. 4).
ATTENTION!
Before changing the attachments or cleaning the
dust bin (11), switch the vacuum cleaner off by
pressing the on/off button (16) and unplug it.
CLEANING AND MAINTENANCE
Cleaning the dust bin (11)
• It is recommended to remove garbage and dust from
the dust bin (11) after every room cleaning.
•
Switch the vacuum cleaner off by pressing the on/off
button (16) and unplug it.
• Holding the handle (12), press the lock (13) and
remove the dust bin (11) (pic. 5).
• Place the dust bin (11) over a garbage bin.
• Pull the lock (24) and open the lower lid (25) (pic. 6).
• Remove accumulated dust and garbage from dust
bin (11).
• Close the lid (25).
• Install the dust bin (11) back to its place and make
sure that the dust bin (11) is fixed properly.
