manualshive.com logo in svg

Brave VH1322GC, Owner/Operator And Safety Manual

Introducing the Brave VH1322GC, a robust and reliable owner/operator tool designed to tackle your toughest tasks. Unlock the full potential of this powerful machine by downloading the complimentary owner/operator and safety manual, available for free at manualshive.com. Empower yourself with essential maintenance and operating instructions, ensuring a safe and successful experience.

Share
Download
background image

800-350-8739 

17

 

Brave 

 

 

Start-Up Procedure

 

 

Important Notice

 

If your log splitter is equipped with a factory installed engine, do not mix oil 

with the gasoline.  Using mixed oil/gasoline in a four cycle engine can cause 
engine damage.

 

 

 

7

.  Fill the engine’s fuel tank with fresh, clean, lead-free automotive gasoline. 

 

8

.  Attach the spark plug wire and start the engine per the manufacturer’s instructions. 

 

9

.  With  the  engine  running,  push  the  valve  control  handle  to  the  retract  position  and 

retract the cylinder piston.  The cylinder valve will automatically stop the cylinder from 
retracting when it reaches the end of its stroke.  Cycle the log splitter several times. 

 

10

.  Again, check the fluid level in the hydraulic tank and add oil as needed.   Replace 

and tighten the fill cap. 

 

11

.  Your log splitter is now ready to use. 

Summary of Contents for VH1322GC

















































Reviews:

No comments

Related manuals for VH1322GC

Scheppach 3905202915 Translation From Original Manual preview
3905202915
Brand: Scheppach Pages: 108

Brands by name

Popular brands

Load more brands