Brave VH0622 Owner/Operator And Safety Manual Download | Manualshive

Page: 18 / 48

background image

Important Notice

Follow all the instructions listed below before starting or operating your log split-
ter. Failure to do so may result in engine and hydraulic pump damage. Also
read the Briggs & Stratton Operating & Maintenance Instructions. If you do not
have this manual, contact Briggs & Stratton at 800-233-3723 to obtain another
one or download a copy from their web site at www.briggsandstratton.com.

If this log splitter is purchased without an engine, the customer assumes all liabilities that
might arise from an engine that is incompatible with the design of the log splitter. Also,
any unauthorized changes or modifications to the log splitter will void all warranties.

1

. Fill the hydraulic tank with 3.8 gallons of SAE 10W tractor hydraulic oil or automatic

transmission fluid such as Dextron III. The tank is full when the oil level is approxi-
mately one inch from the top of the tank. Do not tighten the fill cap at this time.

NOTE:

The total hydraulic system oil capacity for this unit is 5.4 gallons.

2

. Fill the engine’s crank case with the engine manufacturer’s recommended oil.

3

. Lubricate the surface of slide rail with grease. This will help to prevent wear between

the slide plates and the slide rail.

4

. Remove the spark plug wire from the engine. This prevents the engine from starting

until the hydraulic pump and cylinder are completely filled with oil. Make sure the
spark plug wire is held away from the spark plug with string or other nonconductive
material.

5

. Push the valve control handle, with one hand, to the forward (extend) position

(towards the front of the cylinder). Pull the engine starter cord, with the other hand,
(approximately 15 times) until the cylinder piston moves forward. (Keep everything
away from the pusher plate and slide wedge during this step.)

NOTE:

Extending the cylinder piston draws the hydraulic fluid through the system and

expels any trapped air in the system.

6

. Check the fluid level in the hydraulic tank and add oil as needed.

Be careful not to spill fuel when filling the engine. If fuel should spill,
quickly wipe off and allow the excess fuel to evaporate before continu-
ing. Fuel and fuel vapors are highly flammable and can cause personal
injury or even death when ignited.

WARNING

Brave Products, Inc.

16

800-350-8739

Start-Up Procedure

«
...
16
17
18
19
20
...
»

Summary of Contents for VH0622

















































Reviews:

No comments

Related manuals for VH0622

Brand: power King Pages: 11

Brand: K&S Pages: 10

Brand: Echo Pages: 1

Brand: POWER DOG Pages: 18

Brand: Oxdale Pages: 15

Brand: Oxdale Pages: 20

Brand: Craftsman Pages: 8

Brand: Craftsman Pages: 60

Brand: Craftsman Pages: 96

Brand: Craftsman Pages: 29

Brand: Craftsman Pages: 56

Brand: Craftsman Pages: 60

Brand: Craftsman Pages: 28

Brand: Craftsman Pages: 28

Brand: Toro Pages: 48

Brand: Scheppach Pages: 79

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands