background image

BRPRC110HE, REV B 

REV 3/20 

 

 

 

 

 

 

 

 

SAFETY INTRODUCTION 

 

Your safety, and the safety of others, is very important.  To help you make informed 

decisions about safety, we have provided operating procedures and other information on 

labels and in this manual.  This information alerts you to potential hazards that could hurt 

you or others. 

 

This safety alert symbol is used to indicate safety instructions.  Follow these 

instructions to avoid personal injury and/or property damage.  Read and follow all 

instructions in this manual and the included engine manual. 

 

You will find important safety information in a variety of forms, including: 

 

Safety Labels 

– on the mower. 

 

Safety Messages

 – preceded by a safety alert symbol         and one of three signal 

words:  

DANGER, WARNING, 

or 

CAUTION. 

 

These signal words mean: 

 

DANGER:

  Indicates an imminently hazardous situation that, if not avoided, will result in 

death or serious injury.  This signal word is to be limited to the most extreme situations 

typically for machine components which, for functional purposes, cannot be guarded. 

 

WARNING:

  Indicates a potentially hazardous situation that, if not avoided, could result in 

death or serious injury, and includes hazards that are exposed when guards are removed.  

It may also be used to alert against unsafe practices. 

 

CAUTION:

  Indicates a potentially hazardous situation that, if not avoided, may result in 

minor or moderate injury.  It may also be used to alert against unsafe practices. 

 

This entire manual is filled with important safety information.  Please read it 

carefully. 

Summary of Contents for BRPRC110HEB






















Reviews: