manualshive.com logo in svg

Braun SpaceCom, Service Manual, Page: 14 / 126

Share
Download
Braun SpaceCom Service Manual Download Page 14

System Overview 

1

 

1 -   2

  SpaceStation, 2.0 gb

Physical construction

SpaceStation without SpaceCom

The SpaceStation consists of the housing and the housing back

panel.

The power supply with power connector and power socket for an-

other SpaceStation is installed on the right side in the housing.

The pumps in the SpaceStation are locked by 8 locking claws

which are built in the housing as subsystem “module locking”. This

subsystem also contains the locking for a SpaceCover or another

SpaceStation.

The pump is released with a release button on the left side of the

housing.

The pumps are connected to the system via the connectors “F2A“

to “F2D“ (from top to bottom) which are integrated in the inter-

face board, while the SpaceStation is connected to other modules

via the connectors “F3“, “F4” and “F5”. The interface board with

connectors is installed on the left side in the housing.

Abb.: 1 - 2   SpaceStation, front view

Legende zu Abb. 1 - 2:

ItemDesignation

1

Pump lock

2

Connector “F5“

3

Module lock

4

Connector “F1B“ (mains output)

5

Tube guide

6

Connector “F2D“

1

2

4

5

6

3

2.0

Summary of Contents for SpaceCom































































































































Reviews:

No comments