11
gearbox from the shaft by turning counter-
clockwise.
Caution
•
Never use the puree accessory in a saucepan
over direct heat.
•
Always remove the saucepan from the heat and
allow to cool slightly.
•
Sit the saucepan or bowl on a stable, flat surface,
and support it with your free hand.
•
Do not tap the puree accessory on the side of the
cooking vessel during or after use. Use a spatula
to scrape excess food away.
•
For best results when mashing never fill a
saucepan or bowl more than half full with food.
•
Do not process more than one batch without
interruption.
•
Let the appliance cool down for 4 minutes before
you continue processing.
Recipe Example: Mashed Potatoes
2.2 lbs / 1 kg cooked potatoes
7 fl. oz. / 200 ml warm milk
Place the potatoes in a bowl and mash for 30
seconds (3/4 way on the Smart Speed switch)
Add the milk. Resume mashing for another 30
seconds.
Chopper Accessory (D)
The choppers (10/11) are perfectly suited for
chopping hard cheese, onions, herbs, garlic,
vegetables, bread, crackers and nuts.
Use the «hc» chopper (10) for fine results.
Maximum operation time and capacity for the «hc»
chopper: For soft and wet ingredients fill container
max. half full, operating time max. 2 minutes.
For hard or dry ingredients fill container with max.
100 g (3.5 oz), operating time max. 30 seconds.
Immediately stop processing when motor speed
decreases and/or strong vibrations occur.
Use the «bc» chopper (11) for larger quantities and
for hard foods.
Furthermore, the «bc» chopper offers a variety of
other applications like shakes, drinks, purées,
batter, meat or crushed ice.
For processing of liquids the quantity should not
exceed 2/3 of working bowl. For best results of hard
food processing fill the container with max. 300 g
(10.5 oz). For ice crushing use max. 6 cubes.
Refer to the Processing Guide D for maximum
quantities and recommended speeds.
Before Use
•
Pre-cut foods into small pieces for easier
chopping.
•
Remove any bones, tendons and gristle from
meat to help prevent damage to the blades.
•
Make sure the anti-slip rubber ring (10d) is
attached to the bottom of the chopper bowl.
Assembly and Operation
•
Carefully remove the plastic cover from the
blade.
•
The blade (10b/11b/11c) is very sharp! Always
hold it by the upper plastic part and handle it
carefully.
•
Place the blade on the center pin of the chopper
bowl (10c/11d). Press it down and give it a turn
so that it locks into place.
•
Fill the chopper with food and put on the lid
(10a/11a).
•
Align the chopper with the motor part (4) and
click together.
•
To operate the chopper, switch on the appliance.
During processing, hold the motor part with one
hand and the chopper bowl with the other.
•
Always chop harder foods (e.g. parmesan
cheese) at full speed.
•
When chopping is complete, unplug and press
the release buttons (5) to detach the motor part.
•
Lift the lid up. Carefully take out the blade before
pouring out the contents of the bowl. To remove
the blade, slightly turn it then pull it off.
Caution
•
«hc» chopper is not suitable for meat processing.
•
Do not use the chopper accessories (10/11) with
chopping blades to process extremely hard
foods, such as unshelled nuts, ice cubes, coffee
beans, grains, or hard spices e.g. nutmeg.
Processing these foods could damage the
blades.
•
Only the «bc» chopper accessory (11) with the
special ice blade is allowed to crush ice cubes.
•
Never place the chopper bowl in the microwave
oven.
Food Processor Accessory
The food processor accessory (12) can be used for:
•
Chopping, blending and mixing light batter;
•
slicing, shredding, julienning, and making french
fries.
Chopping (E)
Using the blade (12h) you can chop meat, hard
cheese, onions, herbs, garlic, vegetables, bread,
crackers, and nuts.
For processing of liquids the quantity should not
exceed 1/2 of working bowl.
For best results of hard food processing fill the
container with max. 400 g (14 oz).
Refer to the Processing Guide D for maximum
quantities and recommended speeds.
Before Use
•
Pre-cut foods into small pieces for easier
chopping.
5722112674_MQ9097X_USCA_S6-28.indd 11
5722112674_MQ9097X_USCA_S6-28.indd 11
06.06.17 10:21
06.06.17 10:21