background image

Page 8

Attendants must become familiar 
with the vehicle ramp access door 
system and interlock(s), as well 
as the proper operation of the 
ramp.  

Vehicle ramp access door con-

fi

gurations and operation proce-

dures vary.  Ensure the ramp door 
is fully open before activating the 
ramp (an interlock typically pre-
vents ramp operation unless the 
door is fully open).  Attendants 
and passengers must keep clear 
of the area in which the power 
door operates.  Ensure the path 
is clear before closing the door.  
Be sure the door is fully closed 
before attempting to drive the ve-
hicle (interlocks typically ensure 
this).  

Interlocks are required by nearly 
all transit authorities.  Vehicle 
interlocks typically prevent vehicle 
motion if the ramp is not stowed.  
In some cases, the ramp cannot 
be operated if interlock conditions 
are not met.  Interlock require-
ments may include:  the vehicle 
transmission must be engaged in 
Park, the parking brake must be 
engaged, the ramp access door 
must be fully open and/or others.  
Multiple interlocks may exist.  

Instructions for operation of 
interlocks and door systems will 
not be addressed in this manual 
due to the variety of procedures 
required for operating them.    

General instructions for safe 
operation of the ramp are pro-
vided.  Ramp safety and ramp 
passenger safety information is 
included.  

It is the responsibil-

ity of the attendant 

to properly 

open and close the ramp access 
door(s), to activate interlock(s), to 
properly activate the ramp power 
functions as well as assist ramp 
passengers.

Do not operate the ramp if you 
suspect ramp damage, wear or 
any abnormal condition.  Dis-
continue use immediately and 
contact The Braun Corporation 
at 1-800-THE LIFT

®

.  One of our 

national Product Support repre-
sentatives will direct you to an 
authorized service technician who 
will inspect the ramp. 

  Ramp Access Doors and Interlocks

The RA400 Ramp provides 
vehicle access to people with 
disabilities (wheelchair passen-
gers or standees using other type 
mobility aids).  The commercial 
oriented RA400 Ramp is operated 
by the transit vehicle driver/atten-
dant.  Unless your transit agency 
has a published policy stating that 
driver/attendants do not aid ramp 
passengers, 

safe entering and 

exiting of ramp passengers is 
the responsibility of the driver/
attendant

.

As stated in the Ramp Operation 
Safety section, all information in 
this manual is provided for the 
safety of passengers, attendants 
and bystanders.  

Recognize the 

seriousness of this information.

   

Read and become familiar with 
all ramp operation safety pre-
cautions, operation notes and 
details, operating instructions and 
manual operating instructions

 

before

 

attempting ramp opera-

tion procedures or assisting ramp 
passengers boarding and exiting 
the vehicle.

  Operation Notes and Details

RAMP OPERATION 

Summary of Contents for FF3248Y-24V










































Reviews: