manualshive.com logo in svg

Branson S83, Owner'S Manual, Page: 27 / 104

Share
Download
Branson S83 Owner'S Manual Download Page 27

 
 
 

 

S83/85 Ultrasonic Generator

 

 

Installation

 

A40-064 Rev 0 

Page 27 

 

3.7.2 

Installation Do’s and Don’ts 

1.  DO make sure you have all necessary system components: the RF cable, the interconnecting 

jumper cables, and the junction boxes. 

2.  DO ensure that the frequency and number of elements (transducers) of the ultrasonic power 

supply matches that of the ultrasonic tank load. 

3.  DO compare the numbers on the RF cable label and the ID plate on the back panel of the 

ultrasonic power supply to make sure they match. 

4.  DO turn off main power switches. 
5.  DO make sure to ground the ultrasonic power supply in accordance with local building and 

safety codes. 

6.  DO check the line voltage on the ID plate for the ultrasonic power supply line voltage to 

ensure it matches your AC source voltage 

7.  DO use Power Modulation mode – after initially filling the ultrasonic tank – to remove large 

obstructive gas bubbles which shield the ultrasonic energy.  Run for 10-15 minutes at 
operating temperature. 

8.  DO maintain the liquid level of the ultrasonic tank with 3 inches of the top – the same level as 

the fill port. 

9.  DO, in application with large parts which displace significant amount of liquid, take care not 

to expose the heaters. 

10.  DO make sure to operate an ultrasonic tank from the same ultrasonic power supply. 
11.  DO ensure parts are at least 2 inches from the radiating surface of the ultrasonic tank or 

immersible transducers.  Do this by positioning a basket or parts rack to maintain the 2-inch 
minimum distance. 

12.  DO ensure parts slowly agitate up and down while ultrasonic cleaning.  This enhances the 

cleaning process by flushing away the contaminates as cavitation removes them. 

13.  DO make sure to open/expose parts to the ultrasonic field as much as possible. 
14.  DO use baskets constructed of ¼ inch mesh or larger.  For small parts, DO use near solid 

bottom baskets. 

 

Don’ts 

1. 

DO NOT place parts directly on the radiating surface of an ultrasonic tank or immersible. 

2. 

During the cleaning process, DO limit the disturbance of the liquid.  Limit flow from fills 
or recirculation to 4-5 gallons per minute. 

3. 

DO NOT ever use highly acidic compounds or flammable chemistries – the C/CH tank 
series and immersible transducers are constructed of 316L stainless steel. 

4. 

DO NOT plug the ultrasonic power supply to AC source until you finish installing the 
ultrasonic tank or tank with immersible transducers. 

5. 

DO NOT operate the ultrasonic power supply with the cover off. 

 

Caution: 

Check the model number of the ultrasonic power supply and the model numbers on the 
ultrasonic tank that you plan to install.  

Equipment damage can occur if the ultrasonic 

power supply model number does not match the number of elements in the ultrasonic tank. 

Before installing, make sure that you turn off the ultrasonic power supply and disconnect your AC 
voltage source.  Leave the ultrasonic power supply disconnected until you finish the installation. 
 

Summary of Contents for S83









































































































Reviews:

No comments