English
- 49 -
Recording a programme
IMPORTANT
: When using a new USB hard drive
reader, it is advisable to first format the disk using the
“Format disk”
option of your television.
Note:
To record a programme, you first have to switch
off the TV and connect a USB device with at least 2.0
speed compatibility and a minimum 1GB capacity
(a minimum capacity of 4GB is recommended),
otherwise an error message will appear. Then turn
on the TV set in order to enable the record function.
Note
: Programmes recorded are saved on your
USB device. You can ‘‘
copy’’
these recordings on a
computer if you want. However, they can be read only
on your television.
Note
: You cannot record radio broadcasts. The
maximum duration of a recording is unlimited. Lip
Sync delay may occur during the timeshifting.
Programmes recorded are divided into 4 GB partitions.
If the write speed of the USB device connected is
insufficient, the recording may fail and the time shift
option may not be available.
As such, it is advisable to use USB devices that are
HD compatible.
Avoid disconnecting your USB device during
recording. If you do, you may damage the device.
The television can support a maximum of two different
partitions. The first partition of the USB disk will be
used for the recording function (PVR).
If signal reception problems occur, it may not be
possible to record some signal data. Also, the images
may be blurry during playback.
The
Record, Play, Pause, Display
buttons (for
PlayListDialog) are not active in Teletext mode. If a
recording starts from the timer when the teletext is
active, the latter will be disabled automatically. Teletext
does not function in multimedia mode.
Time shift recording
Press the
(PAUSE) button while watching a
programme to switch to timeshift mode. When you
use this mode, the programme pauses and the
recording continues.
Press the (PLAY) button or the
(PAUSE) button
again to watch the paused programme. Press the
STOP
button to stop recording and return to real time
broadcast
Note
: This function is not available in radio mode. You may
use the fast forward /fast rewind buttons to browse.
Note
: You cannot use the fast rewind and fast forward buttons
if you are not in play mode.
Instant Recording
Press the
(RECORD) button to start instant
recording of a programme while you're watching it.
The recording will be done based on the EPG. You
can press the
(RECORD) button on the remote
control again to record the next programme on the
EPG (Electronic Programme Guide). In this case, the
programmes scheduled for recording will be displayed
on the screen. Press the
(STOP) button to cancel
instant recording.
Note
: In instant recording mode, you cannot change channels or
watch a source other than that being recorded. When recording
a programme during a time shifting, a warning message will
appear on the screen if your USB device's speed is not sufficient.
Watching recorded programmes
Select the
Recordings library
option under the
media browser
menu. Select one of the recordings
in the list. Press the
OK
button to display the
play
options
. Select an option and press the
OK button.
Note: The display of the main menu and the submenus are
not available when playing recordings.
Press the
(STOP) button to stop playing and return
to the Recordings Library.
Slow forward
If you press the (PAUSE) button while watching a
recorded programme, the slow forward option will be
available. You can use the
button for the slow
forward. To modify the slow forward speed, press the
button repeatedly.
Recording Configuration
Select
the Recording Configuration
option in the
Settings
menu to configure recording parameters.
Format Disc
: You can use the disk formatting option
to format the connected USB disc. Your PIN code will
then be required.
The default PIN code can change depending on
the country selected.
If a PIN code is required to display a menu option,
enter one of the following codes:
4725
,
0000
or
1234
.
IMPORTANT
: Note that all the data contained in
the USB device will be lost and the device will be
formatted using FAT32. Also, if your USB device
does not function properly, you can try to format it.
In most cases, formatting the USB device solves the
problem, however, ALL the data contained in the USB
disc will be lost.
Note :
If the message "USB too slow" appears on the screen
at the start of a recording, try starting the recording again.
If the same error message appears, it is possible that your
USB disk does not have the required speed. Try to connect
another USB disc.
Downloaded from www.vandenborre.be
