Rev001
34
35
www.babyqs.com
BN FIX 123
5.1.
Press the ISOFIX release button and push the ISOFIX
connectors forward as far as possible (fig. 5.1).
5.2.
Push the ISOFIX connectors firectly into the anchorages until
heard an audible sound “click”. (fig. 5.2, 5.3).
5.3.
Grasp the seat body to check the seat if it is fastened tightly
or shakes. If the seat shakes and the ISOFIXconnectors
are pulled out, please repeat the above steps and install it
again. Push the child seat against the vehicle seat back until
the maximum possible extent (fig. 5.4).
5.4.
Pull out the Top Tether and press the tether strap release
button to extend the strap until it is logn enough to hook the
user-ready tether anchorage behind. (fig. 5.5, 5.6)
5.5.
Hook the tether strap hook onto the user-ready anchorages.
See vehicle owned manual (fig. 5.7, 5.8).
5.6.
Pull the tether strap end to tighten the Top Tether (fig. 5.9, 5.10).
NOTE!
The Top Tether will be correctly tightened when the
green mark is displayed.
6. GROUP 2 AND 3. INSTALATION fOR CAR BELT (3 POINTS)
Only GROUP 2/3. From approx. 4 to
12 years of age (15Kg-36Kg)
NOTICE
AND ISOfIx SySTEM
6.1.
Press the ISOFIX release button and push the ISOFIX
connectors forward as far as possible. Push the ISOFIX
connectors firectly into the anchorages until heard an audible
sound “click”. Grasp the seat body to check the seat if it
is fastened tightly or shakes. If the seat shakes and the
ISOFIXconnectors are pulled out, please repeat the above
steps and install it again. Push the child seat against the
vehicle seat back until the maximum possible extent. (fig.
6.1, 6.2, 6.3).
6.2.
With the child sit on the child seat, take the adult belt and
secure the child by passing the lap portion of the belt
through the red waist belt guides (G). Fasten the belt buckle
and make sure the diagonal portion of the belt pass midway
in between the child showlder and neck. (fig. 6.5).
6.3
Make sure the belt is neither folded nor twisted.
6.4
Make sure the belt is tighten.
6.5
Make sure the lap portion of the belt retains the child by the
pelvis not by the abdomen.
7. MANTENANCE HARNESS SySTEM
7.1 Removing the 5-point harness system and cover
7.1.1.
Press adjusting device and pull harness strap towards as far
as you can. Open the cover snap button at the bottom of
seat back as shown right picture (fig. 7.1).
7.1.2.
Loose the harness strap and pull strap out off the strap yoke
(fig. 7.2).
7.1.3.
Pull two harness straps out off cover slot, then separate
strap with buckle metal connector (fig. 7.4, 7.5).
7.1.4.
After above steps, draw whole strap out from the bottom of
seat. (fig. 7.6). Rotate buckle clip to the shown position, (fig.
7.7) then take it out from seat base. (fig. 7.8).
7.1.5.
Remove the 5-point harness system then remove the
headrest cover and the shell cover (fig. 7.9).
7.1.6.
To install 5-point harness system follow the previous fixes in
reverse order (fig. 7.9).
Summary of Contents for BNFIX 123 HB-10
