background image

1. Be sure your battery is holding the proper 
charge.
2. Make sure the positive side of the Battery 
Prog Brain (the printed side) is attached to the
positive (+) post of the battery.
3. Check that the Manual Reset Control Knob is 
pointing to the “ON” position.
4. Check that the black ground wire is securely 
attached to the negative (-) post on the battery.

If a warning light for NO CHARGE or BATTERY 
WARNING illuminates on your dashboard, stop 
your vehicle at a safe area and TURN THE 
MANUAL RESET
CONTROL KNOB (located under the 
removable protective cover on the Battery Prog  
Brain unit itself) TO THE “OFF” POSITION. Your 
vehicle will experience a complete loss of 
power unless the “No Charge” problem is 
repaired immediately! This problem is unrelated 
to the Battery Prog Brain and requires assistance 
from a qualified technician.

1. Consult a certified technician. 

1. Make sure that the light on the Remote 
Control is lit when you press the button 
down. If the light does not come on, open the 
Remote Control and replace 
the battery.
2. Hold the Remote Control button down for five 
seconds to activate Battery Prog Brain.
3. Turn the Manual Reset Control Knob to 
“ON”.
4. Check that the black ground wire is securely 
attached to the negative (-) post on the battery.

1. Your car battery may be low in power due to 
Alternator function. 
If it cannot hold a charge, it may be at the end 
of its life cycle.
2. The electrical system might have an 
unknown short. Consult a certified technician.
3. Make sure all lights are off.
4. Disconnect all accessory electronics (radio, 
phone charger, DVD player, etc.) and check 
again. 

AFTER INSTALLATION, THE BATTERY 

BRAIN DOESN’T SEEM TO 

BE WORKING.

AFTER THE BATTERY PROG BRAIN HAS 
DISCONNECTED POWER, 
THE REMOTE CONTROL DOES NOT RESET 
THE POWER.

BATTERY PROG BRAIN IS FREQUENTLY 
DISCONNECTING POWER FOR 
NO APPARENT REASON.

YOU CANNOT DETERMINE A BATTERY 
PROG BRAIN INSTALLATION CONFIGURATION
FOR YOUR VEHICLE OR LOCATE BATTERY 
CONNECTIONS.

WHAT TO DO

WHAT TO DO

IMPORTANT NOTE:

WHAT TO DO

WHAT TO DO

Trouble Shooting

 PROG

Summary of Contents for Battery Prog Brain











Reviews: